Ahmedabad venue
Stall fabrication at Open Exhibition Grounds, Ahmedabad
Open grounds where hangar-style German-tent exhibitions and trade fairs are set up.
17
Ahmedabad venues covered
6
Named exhibition venues
11
Venue categories
Tier 1
Gujarat market
Exhibiting at Open Exhibition Grounds, Ahmedabad
Open grounds where hangar-style German-tent exhibitions and trade fairs are set up. Our crews work to the organiser's build-up window at this venue, pre-assembling in the workshop so site time goes on assembly rather than fabrication.
A venue imposes a rulebook, and the stall has to be built to it: how high you can go, whether you can hang anything, what you may fix into the floor, how much power you get and which hours you can work. We read that rulebook at design stage, not at build-up.
Placed against the rest of the Ahmedabad list, Open Exhibition Grounds, Ahmedabad is the most open end of it — no walls, no ceiling, no fixed limits, and no shelter either. Knowing that before you design is what stops a stand being drawn for a hall and then built in a ballroom, which is the most expensive revision in this business.
As a Tier 1 exhibition city, Ahmedabad carries 6 named venues as well as 11 venue categories, which is why two shows in the same week can need entirely different builds. The practical consequence of that density is congestion at build-up: shared bays, lift queues and a hard clearance deadline that nobody moves.
Building on an open exhibition ground
Open grounds give a builder the freedom indoor venues cannot: large panels delivered to the stand, height limited by the tent rather than a slab-to-soffit figure, and a vehicle alongside the build for as long as it is needed. The trade is that the specification has to survive rain, wind, heat and dust for the length of the show.
Open exhibition grounds vary from one address to the next even inside Ahmedabad, so the figures below are the pattern rather than the contract. The organiser's pack for your show is what we actually design to.
What changes at open exhibition grounds
| Build input | At open exhibition grounds |
|---|---|
| Access route & panel sizes | Vehicles usually reach the stand itself, so panel size is limited by the truck and the crew rather than by a door. That is the one real structural advantage an open ground gives a builder. |
| Fixing method | Pegs, ballast and ground anchors, plus fixings into the hangar or tent frame where the organiser permits them. Tall elements are triangulated because there is nothing solid to lean against. |
| Power source | Generator supply with its own distribution and a backup path. Cable runs are long, so voltage drop, protected routing and crossing points across walkways are designed rather than discovered. |
| Floor protection | Raised platform flooring to level uneven ground, keep dust down and give cables a route. Underneath the platform, drainage matters as much as levelling does. |
| Build & strike hours | A longer build-up window than an indoor hall, because tenting, flooring and power all precede the stand. Daylight working is the norm and dust is continuous. |
| Weather & environment | The governing constraint. Rain, wind, heat and dust are all designed for — sealed edges, covered junctions, wind loading on anything tall, and no graphic that cannot take a shower. |
These six are the ones that change the stand rather than the drawing. Confirm them for your edition with the organiser and we will design to the answers; where an answer is unavailable we design to the conservative assumption and revise once it arrives.
How we build for this kind of venue
- Raised platform flooring to level the ground, seal out dust and carry cable runs
- Drainage considered under the platform as carefully as the levels above it
- Edge sealing and covered electrical junctions as standard on an exposed site
- Generator power with its own distribution and a backup path
- A longer build-up window because tenting, flooring and power precede the stand
- Wind loading accounted for on every tall, hanging or fabric element
What to ask the organiser about open exhibition grounds
A quote for open exhibition grounds is an estimate until these answers exist, and a price afterwards. Ask the organiser for them in writing — not because anyone is being difficult, but because the same venue issues different rules for different shows.
Get these in writing before you brief anyone
- Wind-loading limits on tall or hanging elements, and whether any are barred outright
- The build-up sequence, since flooring and tenting have to be finished before stands begin
- The ground surface — levelled earth, hardstanding or turf — and whether pegging is permitted
- Who is responsible for drainage and for standing water during the show
- Whether power is generator or mains, the allocation per stand, and the distance to the connection point
- Vehicle access to the stand itself, and for how long a vehicle may remain
Who exhibits at Ahmedabad venues, and what that changes
Exhibitors at Ahmedabad venues come mainly from chemicals, textiles, diamonds & jewellery, ceramics and engineering — the sectors that fill Gujarat's show floors. Those audiences do not want the same stand, and at open exhibition grounds the difference shows up in the build rather than in the brief: who needs a closed room, who needs a load-rated floor, who needs water and drainage, who needs nothing but a screen and two chairs.
Most Ahmedabad exhibitors are selling to more than one of those audiences, which is an argument for a layout rather than a style. Give the textiles audience the frontage and the diamonds & jewellery audience the back corner, and the stand stops trying to be two things in the same square metre.
Ahmedabad's sector mix and what each needs from a stand
| Sector | What the stand has to do |
|---|---|
| Textiles | Textile buyers handle everything. Rail and drape capacity, a fold-and-compare table, true-colour lighting, and a lockable store for the sample ranges that leave the stand each day. |
| Diamonds & jewellery | Jewellery needs locked and individually lit cases, a seated viewing position with true-colour light, and staff positions that keep every case in view from one spot. |
| Ceramics | Ceramics and tiles are heavy and reflective. Load-rated display frames, a layout that shows tile at floor angle as well as on the wall, and lighting that does not glare off glaze. |
| Engineering | An engineering audience reads drawings and specifications, so the stand needs a technical wall, a sample or cutaway to handle, and a table with chairs where a quote can actually be discussed. |
| Chemicals | Chemical exhibitors sell specification rather than appearance. Plan a technical literature wall, a closed meeting space for formulation talk, and a safe display method for anything in a container. |
The sectors listed are the ones that drive exhibiting activity across Gujarat. Where your show draws from more than one of them, the space plan below is where the compromise gets resolved.
Services
What we build at Open Exhibition Grounds, Ahmedabad
Exhibition Stall Design
Concept-to-3D stall design that stops visitors in the aisle.
Stall Fabrication
In-house carpentry, metal and print for flawless builds.
Custom Exhibition Booths
One-of-a-kind booths built around your brand.
Modular Exhibition Stalls
Reusable, quick-install stalls for frequent exhibitors.
Octanorm & System Stalls
Clean aluminium shell-scheme and system booths.
Double-Decker Stalls
Two-storey stands that double your space.
Pavilion Design
State, industry and association pavilions.
Country Pavilions
National pavilions at Indian and global expos.
Trade Show Booths
High-impact booths for B2B trade shows.
Exhibition Stand Builders
End-to-end stand building with on-site crews.
Event Stage Fabrication
Stages, backdrops and sets for events.
AV & LED Wall Support
LED walls, sound, screens and AV crews.
Stall sizes and lead times for Open Exhibition Grounds, Ahmedabad
Most stands at a venue like this fall between 9 and 72 sq.m. The table below uses the same formula as our stall planner — storage at 10% of area up to 18 sq.m and 15% above, a meeting corner at 5% unless you are hosting meetings, display taking the remainder — so you can sanity-check a quote against the space you have actually booked.
The figures are the same ones our stall planner uses, so a quote can be checked against them line by line: storage at 10% of the area up to 18 sq.m and 15% above it, a meeting corner at 5% unless you are actually hosting meetings, display taking whatever remains, one staff member per 9 sq.m, and the number of visitors who can stand in the stall at once coming out at display area divided by 2.5.
Space, staffing and lead time by stall size
| Stall size | Footprint | Likely layout | Display | Staff | Visitors at once | Build weeks |
|---|---|---|---|---|---|---|
| 9 sq.m | 3 × 3 m | Inline or corner | 7.6 sq.m | 2 | 3 | 3 |
| 18 sq.m | 3 × 6 m | Inline or corner | 15.3 sq.m | 2 | 6 | 3 |
| 36 sq.m | 6 × 6 m | Corner or three-side open | 28.8 sq.m | 4 | 11 | 4 |
| 54 sq.m | 6 × 9 m | Corner or three-side open | 43.2 sq.m | 6 | 17 | 5 |
| 72 sq.m | 6 × 12 m | Three-side open or island | 57.6 sq.m | 8 | 23 | 5 |
Custom stalls typically run ₹9,000–₹18,000 per sq.m for the build; modular and octanorm construction costs less, and an upgraded shell scheme less again. AV, furniture, flooring, transport and taxes are quoted on separate lines.
Designing a stand that works at Open Exhibition Grounds, Ahmedabad
On an open ground your competition is the sky, not the neighbouring stand. Height, a roof line of your own and lighting that still works at dusk are what make a stand findable from the far side of the ground.
The most common mistake here is treating every wall as equally valuable. One face does most of the work; identify it from the stand plan, spend the budget on it, and treat the rest as support.
The buyers at this venue tend to come from chemicals, textiles and diamonds & jewellery. That shapes the brief more than the aesthetics do — a chemicals visitor is looking for evidence, not atmosphere.
How a build at open exhibition grounds runs
01
Read the venue pack
The job starts with paperwork rather than with a concept. We want the stand plan, the access route, the power allocation and the permitted working hours in writing, and at open exhibition grounds we pay particular attention to whether tenting and flooring are provided by the organiser, and when they will be finished.
02
Design to the limits
Design happens against the constraints rather than around them, so platform flooring, sealed edges, wind loading on tall elements and generator distribution is a starting condition here rather than a late revision. What you approve in 3D is therefore something that can actually be built in this room.
03
Build and test in the workshop
Carpentry, metalwork, spray finishing, large-format print and electrical assembly all happen in-house, and the whole stall is assembled once before it ships. That is what turns a short on-site window into enough time.
04
Install, hand over, strike
A named project manager and the crew that pre-assembled the stall install it to the drawing and hand over a working stand. Site care is part of that rather than an afterthought: levelling, dust sealing at the platform edges and covered electrical junctions. The same crew returns to dismantle and clear the stand inside the organiser's window.
What else is in Ahmedabad
Ahmedabad gives you more than one kind of room. Alongside this page we cover 6 named exhibition venues in the city — Helipad Exhibition Centre, Gandhinagar, Mahatma Mandir Convention Centre, Gandhinagar, Gujarat University Exhibition Hall, Ahmedabad Management Association, GMDC Ground and Sabarmati Riverfront Event Centre. Read by what each one calls itself, that list comprises 2 purpose-built exhibition and trade centres, 2 open grounds and maidans, 1 convention centre and 1 event venue: 4 different build specifications inside one city.
Underneath the named venues sit the 11 venue categories we cover in every city, Ahmedabad included: university & college campuses, industry association halls, stadium & sports complexes, corporate campus event spaces, industrial estate expo grounds, government exhibition grounds, resort & lawn venues, 5-star hotel ballrooms, convention & banquet halls, open exhibition grounds and mall atriums. A large share of exhibiting activity in India happens in those rooms rather than in exhibition halls, which is why they get their own pages rather than a footnote.
Named Ahmedabad venues, read by what each one calls itself
| Venue | Type read from the name | What that implies for a stand |
|---|---|---|
| Helipad Exhibition Centre, Gandhinagar | Purpose-built exhibition or trade centre | In a purpose-built hall you are one of many stands with identical freedoms, so differentiation comes from the things the hall allows and most exhibitors never use: height, light and a clear reason to step in off the aisle.. |
| Mahatma Mandir Convention Centre, Gandhinagar | Convention centre | A pillar-less hall gives you a long sightline down the aisle, which makes the face that reads from thirty metres away worth more than the one a visitor sees standing in front of you. |
| Gujarat University Exhibition Hall | Purpose-built exhibition or trade centre | In a purpose-built hall you are one of many stands with identical freedoms, so differentiation comes from the things the hall allows and most exhibitors never use: height, light and a clear reason to step in off the aisle.. |
| Ahmedabad Management Association | Event venue | Settle the one visitor action the stand exists to produce, then judge every design decision against it. |
| GMDC Ground | Open ground or maidan | On an open ground your competition is the sky, not the neighbouring stand. |
| Sabarmati Riverfront Event Centre | Open ground or maidan | On an open ground your competition is the sky, not the neighbouring stand. |
A venue's name is a strong hint and not a specification. We confirm height, rigging, fixing, power and hours from the organiser's pack for your edition before design sign-off.
Every Ahmedabad venue we cover
Build-up
Build-up, access and approvals in Ahmedabad
In Ahmedabad the schedule is the organiser's, not yours — which means the build has to be designed around a fixed window, a shared bay and a queue. Pre-assembly in the workshop is what turns that window from a risk into a routine.
You can take the whole scope or just part of it. Most exhibitors take design and build together and add AV and furniture to the same quote, because the alternative is reconciling three delivery schedules yourself.
What we handle for you
- Organiser drawings, electrical load details and approvals in the format Ahmedabad organisers ask for
- Design checked against height, rigging, fixing and fire rules before sign-off
- Pre-assembly and electrical testing in the workshop before dispatch
- Transport, installation and an on-site crew inside the build-up window
- Dismantle and clearing the stand inside the dismantle period
Exhibiting elsewhere in Gujarat
Beyond Ahmedabad we build in 9 other Gujarat cities: Surat, Vadodara, Rajkot, Gandhinagar, Bhavnagar and Jamnagar, plus 3 others. Same drawings, same workshop, same project manager — which is what makes a second city cheaper than the first rather than a repeat of it.
Because we cover open exhibition grounds in all 10 Gujarat cities on our list, a stand designed for this venue type is designed for the state. The structure, the fixing method and the power assumptions carry over; only the footprint and the graphics change.
If this venue is one stop on a programme, say so at design stage. A stand drawn to be reused is drawn differently — demountable joints, numbered panels, graphics on replaceable skins and a storage footprint that fits a standard crate — and retrofitting that later costs more than building it in.
01
Brief
Share stall size, expo and goals. We call within 2 hours.
02
3D Design
Photoreal concepts in 48 hours, revised until perfect.
03
Fabrication
Built and pre-assembled in our own workshops.
04
Install & Show
On-site crew builds, hands over and dismantles.
FAQ
Venue FAQ
Can you build at Open Exhibition Grounds, Ahmedabad?+
Yes. We build at open exhibition grounds throughout Ahmedabad, covering design, fabrication, installation and dismantle inside the organiser's window.
What does a stall at Open Exhibition Grounds, Ahmedabad cost?+
Custom stalls typically range from ₹9,000 to ₹18,000 per sq.m depending on size, finishes and AV; modular and octanorm builds cost less. Share your stand size and show dates for an itemised quote.
Can you work to a shell scheme at Open Exhibition Grounds, Ahmedabad?+
Yes. Where the organiser supplies shell scheme panels we upgrade them with printed fabric or vinyl, raised flooring, spotlights and a branded counter, which lifts the stand a long way at modest cost.
Can you provide AV, lighting and furniture at Open Exhibition Grounds, Ahmedabad?+
Yes — LED walls, screens, lighting, furniture, flooring and carpeting can be bundled with the stall build on a single quote.
How early should I book for a show at Open Exhibition Grounds, Ahmedabad?+
Four to six weeks ahead for a custom stall and eight or more for a double-decker or pavilion. Urgent builds in seven to ten days are possible with a simplified design.
What are the build-up timings at Open Exhibition Grounds, Ahmedabad?+
Build-up windows are set by the organiser for each show rather than by the venue alone, so we confirm them in writing for your edition and plan the build — including night shifts if needed — around them.
What happens to an open-ground stand if it rains?+
A stand designed for the site takes it. Platform flooring lifts the build clear of standing water, edges are sealed, electrical junctions are covered, and graphics are specified in materials that tolerate a wetting rather than paper-faced boards that do not.
How is power supplied on an open exhibition ground?+
Usually by generator, with distribution run out to the stands and a backup path for critical loads. We confirm the allocation and the distance to the connection point in advance, because long cable runs change both the cable specification and the cost.
Do you design differently for chemicals exhibitors here?+
Yes. Ahmedabad's show calendar is driven by chemicals, textiles, diamonds & jewellery, ceramics and engineering, and the sector decides the fundamentals — how much product has to be on open display, how private the meeting space needs to be, whether the floor has to carry load and whether water, drainage or three-phase power are required. We brief against the sector before the identity.
Can the same stand be used at another Gujarat venue?+
Usually, if it is built for it. We cover 10 Gujarat cities including Ahmedabad, Surat, Vadodara and Rajkot, and a frame-and-skin stand can be stored, re-skinned with new graphics and rebuilt at the equivalent venue elsewhere in the state. Say so at design stage, because a reusable stand is detailed differently.
What is the biggest risk at open exhibition grounds?+
Discovering a constraint after fabrication. Flooring, tenting and generator power all precede your stand on an open ground, so a crew planned in for the first available day arrives before the site is ready for them. That is why we ask for the access route, the fixing rules, the power allocation and the build-up window in writing before anything is cut, rather than treating any of them as a site problem.
More in Ahmedabad
Other Gujarat cities we cover
Exhibiting soon? Let's build your stall.