Aurangabad venue
Stall fabrication at Open Exhibition Grounds, Aurangabad
Open grounds where hangar-style German-tent exhibitions and trade fairs are set up.
13
Aurangabad venues covered
2
Named exhibition venues
11
Venue categories
Tier 2
Maharashtra market
Exhibiting at Open Exhibition Grounds, Aurangabad
Open grounds where hangar-style German-tent exhibitions and trade fairs are set up. We design, fabricate, install and dismantle stalls here, with the organiser drawings and approvals prepared as part of the project rather than quoted as an extra.
A venue imposes a rulebook, and the stall has to be built to it: how high you can go, whether you can hang anything, what you may fix into the floor, how much power you get and which hours you can work. We read that rulebook at design stage, not at build-up.
Of the 13 Aurangabad venues we cover, this one occupies the most open end of it — no walls, no ceiling, no fixed limits, and no shelter either. Exhibitors tend to compare venues on footfall and cost; builders compare them on access, fixing and power, and on that measure the gap between the extremes of the Aurangabad list is very wide.
Aurangabad is a growing exhibition market rather than a mature one, and the venues reflect that: 11 venue categories plus 2 named venues. Rooms are shared with other kinds of event, so the paperwork and the hours come from whoever owns the room rather than from an exhibition operator.
Building on an open exhibition ground
Open grounds give a builder the freedom indoor venues cannot: large panels delivered to the stand, height limited by the tent rather than a slab-to-soffit figure, and a vehicle alongside the build for as long as it is needed. The trade is that the specification has to survive rain, wind, heat and dust for the length of the show.
Open exhibition grounds vary from one address to the next even inside Aurangabad, so the figures below are the pattern rather than the contract. The organiser's pack for your show is what we actually design to.
What changes at open exhibition grounds
| Build input | At open exhibition grounds |
|---|---|
| Access route & panel sizes | Vehicles usually reach the stand itself, so panel size is limited by the truck and the crew rather than by a door. That is the one real structural advantage an open ground gives a builder. |
| Fixing method | Pegs, ballast and ground anchors, plus fixings into the hangar or tent frame where the organiser permits them. Tall elements are triangulated because there is nothing solid to lean against. |
| Power source | Generator supply with its own distribution and a backup path. Cable runs are long, so voltage drop, protected routing and crossing points across walkways are designed rather than discovered. |
| Floor protection | Raised platform flooring to level uneven ground, keep dust down and give cables a route. Underneath the platform, drainage matters as much as levelling does. |
| Build & strike hours | A longer build-up window than an indoor hall, because tenting, flooring and power all precede the stand. Daylight working is the norm and dust is continuous. |
| Weather & environment | The governing constraint. Rain, wind, heat and dust are all designed for — sealed edges, covered junctions, wind loading on anything tall, and no graphic that cannot take a shower. |
Every row here is a design input rather than a detail. Two stands of identical area in Aurangabad can need completely different engineering because these six answers differ, which is why we settle them before anything is cut.
How we build for this kind of venue
- Wind loading accounted for on every tall, hanging or fabric element
- A longer build-up window because tenting, flooring and power precede the stand
- Drainage considered under the platform as carefully as the levels above it
- Panels sized by the truck and the crew rather than by a door
- Generator power with its own distribution and a backup path
- Raised platform flooring to level the ground, seal out dust and carry cable runs
What to ask the organiser about open exhibition grounds
Send the organiser this list before you commission anything. Each answer removes a contingency from the quote, and at open exhibition grounds two or three of them change the structure rather than the finish.
Get these in writing before you brief anyone
- Whether tenting or a hangar is provided by the organiser, and the clear height under it
- Overnight security arrangements on an open site
- Vehicle access to the stand itself, and for how long a vehicle may remain
- Whether power is generator or mains, the allocation per stand, and the distance to the connection point
- Who is responsible for drainage and for standing water during the show
- The ground surface — levelled earth, hardstanding or turf — and whether pegging is permitted
Who exhibits at Aurangabad venues, and what that changes
The sector mix in Aurangabad is automobile, engineering, pharma, textiles and real estate, and each of those brings its own non-negotiables onto a stand. The table below is what we design against at open exhibition grounds before a single visual is drawn, because most of these requirements are structural or electrical rather than decorative.
Mixed-sector shows are the harder case. Engineering and pharma visitors want opposite things from the same footprint, and the resolution is zoning rather than compromise: open display on the aisle face, a closed or semi-closed corner behind it, and storage that keeps the difference invisible.
Aurangabad's sector mix and what each needs from a stand
| Sector | What the stand has to do |
|---|---|
| Engineering | An engineering audience reads drawings and specifications, so the stand needs a technical wall, a sample or cutaway to handle, and a table with chairs where a quote can actually be discussed. |
| Pharma | A pharma audience talks in private. A closed meeting corner, lockable sample storage, a wipe-clean dispensing counter and literature capacity matter more than open display area. |
| Textiles | Textile buyers handle everything. Rail and drape capacity, a fold-and-compare table, true-colour lighting, and a lockable store for the sample ranges that leave the stand each day. |
| Real estate | Real estate sells on models and screens. A scale model on a lit plinth, large visuals at eye height, and several seated pockets where a booking conversation can run twenty minutes. |
| Automobile | An automobile and components audience wants to touch the part. Plan a load-rated display platform, a cutaway or turntable at hip height, and circulation wide enough for a crowd around one vehicle. |
The sectors listed are the ones that drive exhibiting activity across Maharashtra. Where your show draws from more than one of them, the space plan below is where the compromise gets resolved.
Services
What we build at Open Exhibition Grounds, Aurangabad
Exhibition Stall Design
Concept-to-3D stall design that stops visitors in the aisle.
Stall Fabrication
In-house carpentry, metal and print for flawless builds.
Custom Exhibition Booths
One-of-a-kind booths built around your brand.
Modular Exhibition Stalls
Reusable, quick-install stalls for frequent exhibitors.
Octanorm & System Stalls
Clean aluminium shell-scheme and system booths.
Double-Decker Stalls
Two-storey stands that double your space.
Pavilion Design
State, industry and association pavilions.
Country Pavilions
National pavilions at Indian and global expos.
Trade Show Booths
High-impact booths for B2B trade shows.
Exhibition Stand Builders
End-to-end stand building with on-site crews.
Event Stage Fabrication
Stages, backdrops and sets for events.
AV & LED Wall Support
LED walls, sound, screens and AV crews.
Stall sizes and lead times for Open Exhibition Grounds, Aurangabad
Most stands at a venue like this fall between 9 and 72 sq.m. The table below uses the same formula as our stall planner — storage at 10% of area up to 18 sq.m and 15% above, a meeting corner at 5% unless you are hosting meetings, display taking the remainder — so you can sanity-check a quote against the space you have actually booked.
Lead time is the column exhibitors underestimate. Three weeks is the base for a custom build, four from 24 sq.m and five from 54 sq.m, and those are fabrication weeks after design sign-off rather than from the day you first call. At open exhibition grounds the build-up window itself is rarely the problem; the approval and fabrication time ahead of it usually is.
Space, staffing and lead time by stall size
| Stall size | Footprint | Likely layout | Display | Staff | Visitors at once | Build weeks |
|---|---|---|---|---|---|---|
| 9 sq.m | 3 × 3 m | Inline or corner | 7.6 sq.m | 2 | 3 | 3 |
| 18 sq.m | 3 × 6 m | Inline or corner | 15.3 sq.m | 2 | 6 | 3 |
| 36 sq.m | 6 × 6 m | Corner or three-side open | 28.8 sq.m | 4 | 11 | 4 |
| 54 sq.m | 6 × 9 m | Corner or three-side open | 43.2 sq.m | 6 | 17 | 5 |
| 72 sq.m | 6 × 12 m | Three-side open or island | 57.6 sq.m | 8 | 23 | 5 |
Custom stalls typically run ₹9,000–₹18,000 per sq.m for the build; modular and octanorm construction costs less, and an upgraded shell scheme less again. AV, furniture, flooring, transport and taxes are quoted on separate lines.
Designing a stand that works at Open Exhibition Grounds, Aurangabad
On an open ground your competition is the sky, not the neighbouring stand. Height, a roof line of your own and lighting that still works at dusk are what make a stand findable from the far side of the ground.
Visitors decide whether to enter from several metres away, so the stand has to answer "what do you do?" before it answers anything else. One legible line at eye height does more than a wall of product shots.
Exhibitors here come largely from automobile, engineering and pharma, and an automobile audience has specific expectations: product visible, specification available, and somewhere to talk without shouting. We design for that rather than applying a generic layout.
How a build at open exhibition grounds runs
01
Read the venue pack
The job starts with paperwork rather than with a concept. We want the stand plan, the access route, the power allocation and the permitted working hours in writing, and at open exhibition grounds we pay particular attention to whether tenting and flooring are provided by the organiser, and when they will be finished.
02
Design to the limits
Design happens against the constraints rather than around them, so platform flooring, sealed edges, wind loading on tall elements and generator distribution is a starting condition here rather than a late revision. What you approve in 3D is therefore something that can actually be built in this room.
03
Build and test in the workshop
The stall is fabricated and then stood up in our own workshop: panels numbered, graphics trial-fitted, circuits tested and lamps aimed. Problems get found where there is time to fix them rather than at open exhibition grounds at midnight.
04
Install, hand over, strike
On site the work is assembly rather than fabrication, which is the whole point of the previous stage. At open exhibition grounds the install also covers levelling, dust sealing at the platform edges and covered electrical junctions, and the same crew comes back to strike the stand and clear the space.
What else is in Aurangabad
We cover 2 other named exhibition venues in Aurangabad: Ayodhya Nagari Ground and MGM Rukmini Hall. By name they break down into 1 open ground or maidan and 1 auditorium, hall or cultural centre, and the gap between the easiest and the hardest of those to build in is larger than any gap in stall size.
We also cover 11 venue categories in Aurangabad — open exhibition grounds, mall atriums, university & college campuses, industry association halls, stadium & sports complexes, corporate campus event spaces, industrial estate expo grounds, government exhibition grounds, resort & lawn venues, 5-star hotel ballrooms and convention & banquet halls — because most Indian shows outside the top handful of cities happen in a room that was built for something else. Each of those categories has its own access, fixing and power pattern, and each gets its own page.
Named Aurangabad venues, read by what each one calls itself
| Venue | Type read from the name | What that implies for a stand |
|---|---|---|
| Ayodhya Nagari Ground | Open ground or maidan | On an open ground your competition is the sky, not the neighbouring stand. |
| MGM Rukmini Hall | Auditorium, hall or cultural centre | Most of the real traffic at an auditorium venue is in the foyer and during the breaks, so put the stand where people queue and plan for everything to happen in twenty-minute bursts.. |
A venue's name is a strong hint and not a specification. We confirm height, rigging, fixing, power and hours from the organiser's pack for your edition before design sign-off.
Every Aurangabad venue we cover
Build-up
Build-up, access and approvals in Aurangabad
Every Aurangabad venue issues its own build-up schedule, power allocation and list of what you may and may not fix to the structure. We read it before fabrication, because a panel that will not fit through the access door is an expensive thing to discover at the venue.
Everything the stand needs — structure, print, lighting, flooring, furniture, AV and the crew to install and strike it — can be bundled into a single itemised quote with one project manager behind it.
What we handle for you
- Organiser drawings, electrical load details and approvals in the format Aurangabad organisers ask for
- Design checked against height, rigging, fixing and fire rules before sign-off
- Pre-assembly and electrical testing in the workshop before dispatch
- Transport, installation and an on-site crew inside the build-up window
- Dismantle and clearing the stand inside the dismantle period
Exhibiting elsewhere in Maharashtra
Aurangabad is one of 10 Maharashtra cities on our list, alongside Mumbai, Pune, Navi Mumbai, Thane and Nagpur, plus 4 more. For an exhibitor doing a state circuit that matters practically: the structure travels, the graphics are reprinted, and nobody has to re-engineer a stand for each stop.
Open exhibition grounds are not unique to Aurangabad either: we cover the same category in all 10 of the Maharashtra cities on our list, which means the access, fixing and power pattern described above travels with you. A stand built for open exhibition grounds here is usually re-skinnable for the equivalent venue in the next city rather than rebuildable.
Running several cities in a season works best with one structure and several graphic sets. The panels are numbered and stored between shows, each city gets its own print and its own organiser paperwork, and the same project manager carries the job from the first show to the last.
01
Brief
Share stall size, expo and goals. We call within 2 hours.
02
3D Design
Photoreal concepts in 48 hours, revised until perfect.
03
Fabrication
Built and pre-assembled in our own workshops.
04
Install & Show
On-site crew builds, hands over and dismantles.
FAQ
Venue FAQ
Can you build at Open Exhibition Grounds, Aurangabad?+
Yes. We build at open exhibition grounds throughout Aurangabad, covering design, fabrication, installation and dismantle inside the organiser's window.
What does a stall at Open Exhibition Grounds, Aurangabad cost?+
Custom stalls typically range from ₹9,000 to ₹18,000 per sq.m depending on size, finishes and AV; modular and octanorm builds cost less. Share your stand size and show dates for an itemised quote.
Can you provide AV, lighting and furniture at Open Exhibition Grounds, Aurangabad?+
Yes — LED walls, screens, lighting, furniture, flooring and carpeting can be bundled with the stall build on a single quote.
Can you work to a shell scheme at Open Exhibition Grounds, Aurangabad?+
Yes. Where the organiser supplies shell scheme panels we upgrade them with printed fabric or vinyl, raised flooring, spotlights and a branded counter, which lifts the stand a long way at modest cost.
What are the build-up timings at Open Exhibition Grounds, Aurangabad?+
Build-up windows are set by the organiser for each show rather than by the venue alone, so we confirm them in writing for your edition and plan the build — including night shifts if needed — around them.
Who is on site during build-up at Open Exhibition Grounds, Aurangabad?+
A named project manager and the crew that pre-assembled the stall. They install to the drawing, hand over a working stand and return to dismantle and clear it within the organiser's window.
Is build-up longer on an open ground?+
Yes. Tenting, flooring and power distribution all have to be finished before stand building starts, so the organiser's build-up period is longer than an indoor hall's and the sequence is published. We plan our arrival against that sequence rather than against the first available day.
How is power supplied on an open exhibition ground?+
Usually by generator, with distribution run out to the stands and a backup path for critical loads. We confirm the allocation and the distance to the connection point in advance, because long cable runs change both the cable specification and the cost.
Do you design differently for automobile exhibitors here?+
Yes. Aurangabad's show calendar is driven by automobile, engineering, pharma, textiles and real estate, and the sector decides the fundamentals — how much product has to be on open display, how private the meeting space needs to be, whether the floor has to carry load and whether water, drainage or three-phase power are required. We brief against the sector before the identity.
Can the same stand be used at another Maharashtra venue?+
Usually, if it is built for it. We cover 10 Maharashtra cities including Aurangabad, Mumbai, Pune and Navi Mumbai, and a frame-and-skin stand can be stored, re-skinned with new graphics and rebuilt at the equivalent venue elsewhere in the state. Say so at design stage, because a reusable stand is detailed differently.
What is the biggest risk at open exhibition grounds?+
Discovering a constraint after fabrication. Flooring, tenting and generator power all precede your stand on an open ground, so a crew planned in for the first available day arrives before the site is ready for them. That is why we ask for the access route, the fixing rules, the power allocation and the build-up window in writing before anything is cut, rather than treating any of them as a site problem.
More in Aurangabad
Other Maharashtra cities we cover
Exhibiting soon? Let's build your stall.