Siliguri venue
Stall fabrication at University & College Campuses, Siliguri
Auditoriums and grounds used for education fairs, tech fests and placement expos.
11
Siliguri venues covered
0
Named exhibition venues
11
Venue categories
Tier 2
West Bengal market
Exhibiting at University & College Campuses, Siliguri
Auditoriums and grounds used for education fairs, tech fests and placement expos. Our crews work to the organiser's build-up window at this venue, pre-assembling in the workshop so site time goes on assembly rather than fabrication.
A venue imposes a rulebook, and the stall has to be built to it: how high you can go, whether you can hang anything, what you may fix into the floor, how much power you get and which hours you can work. We read that rulebook at design stage, not at build-up.
Of the 11 Siliguri venues we cover, this one occupies the institutional end of it — many small stands, a modest budget and a timetable that belongs to the campus. Exhibitors tend to compare venues on footfall and cost; builders compare them on access, fixing and power, and on that measure the gap between the extremes of the Siliguri list is very wide.
Siliguri is a Tier 2 exhibition market in West Bengal, which changes the venue question rather than the build quality. There is no single dedicated exhibition centre on our list for the city, plus 11 venue categories, so shows share their rooms with weddings, conferences and civic events and your build has to fit around bookings made before yours.
Building on a university or college campus
Campus auditoriums and grounds host education fairs, tech fests and placement expos, where a large number of small stands have to go up quickly against an academic calendar and a modest budget. Vehicle access is restricted to particular gates at particular hours, power comes off limited campus distribution shared with the building's normal use, and the build is worked around classes, examinations and campus security timings.
University & college campuses vary from one address to the next even inside Siliguri, so the figures below are the pattern rather than the contract. The organiser's pack for your show is what we actually design to.
What changes at university & college campuses
| Build input | At university & college campuses |
|---|---|
| Access route & panel sizes | Specific gates in specific hours, then a carry to the auditorium or the ground. Modular sections two people can lift beat panels that need four, because the last fifty metres are usually by hand. |
| Fixing method | Freestanding on finished floors indoors; pegged or ballasted on grounds. Auditorium seating, stages and fittings are left untouched, which means working around them rather than through them. |
| Power source | Limited campus distribution shared with the building's normal use. Lighting loads are kept modest and anything heavy is confirmed with the estate office rather than assumed. |
| Floor protection | Protection over auditorium, corridor and foyer floors, and platform flooring on quadrangles and grounds. Grass and paving are reinstated after strike as part of the job. |
| Build & strike hours | Worked around classes, examinations and campus security timings, which in practice means early mornings, evenings or a weekend rather than a continuous window. |
| Weather & environment | Depends on the space, and many campus fairs run indoors and outdoors at once — which makes them two specifications under one brief. |
These six are the ones that change the stand rather than the drawing. Confirm them for your edition with the organiser and we will design to the answers; where an answer is unavailable we design to the conservative assumption and revise once it arrives.
How we build for this kind of venue
- Sections sized for two people and a stair rather than for a trolley
- Power drawn from limited campus distribution shared with normal use
- Modular systems for fast, repeatable builds across many small stands
- Reusable graphics and frames for a fair that repeats every year
- Built and struck around class, examination and security timings
- Vehicle access restricted to specified gates and hours
What to ask the organiser about university & college campuses
Most of what goes wrong at university & college campuses goes wrong because a question was not asked early. These are the ones worth asking before you brief a designer, let alone a fabricator.
Get these in writing before you brief anyone
- Floor-protection expectations for indoor spaces and reinstatement for grounds
- Which gate vehicles may use, in which hours, and who issues the passes
- Access timings against the academic timetable, including examination restrictions
- Lift availability and the stair route where there is no lift
- Whether the fair runs indoors, outdoors or across both, with a marked plan
- Who on the estate or faculty side signs off the build, and when
Who exhibits at Siliguri venues, and what that changes
Exhibitors at Siliguri venues come mainly from jute, tea, steel, engineering and handicrafts — the sectors that fill West Bengal's show floors. Those audiences do not want the same stand, and at university & college campuses the difference shows up in the build rather than in the brief: who needs a closed room, who needs a load-rated floor, who needs water and drainage, who needs nothing but a screen and two chairs.
Mixed-sector shows are the harder case. Jute and tea visitors want opposite things from the same footprint, and the resolution is zoning rather than compromise: open display on the aisle face, a closed or semi-closed corner behind it, and storage that keeps the difference invisible.
Siliguri's sector mix and what each needs from a stand
| Sector | What the stand has to do |
|---|---|
| Jute | Jute exhibitors show bags, fabric and bulk product. Open stacking, a handling surface, and a packing counter for buyers who will take samples away with them. |
| Tea | Tea selling is tasting. A serviced counter with water, power for an urn, drainage, a clean sampling surface, and a seated corner for a buyer tasting through a range. |
| Steel | Steel exhibitors bring heavy samples — sections, coil, plate. Load-rated plinths, a spread footprint beneath them, a technical wall, and a closed room for tonnage conversations. |
| Engineering | An engineering audience reads drawings and specifications, so the stand needs a technical wall, a sample or cutaway to handle, and a table with chairs where a quote can actually be discussed. |
| Handicrafts | Handicraft stands sell density. Open shelving, sightlines into the stand rather than a counter across the front, and light aimed at the object instead of the ceiling. |
The sectors listed are the ones that drive exhibiting activity across West Bengal. Where your show draws from more than one of them, the space plan below is where the compromise gets resolved.
Services
What we build at University & College Campuses, Siliguri
Exhibition Stall Design
Concept-to-3D stall design that stops visitors in the aisle.
Stall Fabrication
In-house carpentry, metal and print for flawless builds.
Custom Exhibition Booths
One-of-a-kind booths built around your brand.
Modular Exhibition Stalls
Reusable, quick-install stalls for frequent exhibitors.
Octanorm & System Stalls
Clean aluminium shell-scheme and system booths.
Double-Decker Stalls
Two-storey stands that double your space.
Pavilion Design
State, industry and association pavilions.
Country Pavilions
National pavilions at Indian and global expos.
Trade Show Booths
High-impact booths for B2B trade shows.
Exhibition Stand Builders
End-to-end stand building with on-site crews.
Event Stage Fabrication
Stages, backdrops and sets for events.
AV & LED Wall Support
LED walls, sound, screens and AV crews.
Stall sizes and lead times for University & College Campuses, Siliguri
Most stands at a venue like this fall between 9 and 72 sq.m. The table below uses the same formula as our stall planner — storage at 10% of area up to 18 sq.m and 15% above, a meeting corner at 5% unless you are hosting meetings, display taking the remainder — so you can sanity-check a quote against the space you have actually booked.
Lead time is the column exhibitors underestimate. Three weeks is the base for a custom build, four from 24 sq.m and five from 54 sq.m, and those are fabrication weeks after design sign-off rather than from the day you first call. At university & college campuses the build-up window itself is rarely the problem; the approval and fabrication time ahead of it usually is.
Space, staffing and lead time by stall size
| Stall size | Footprint | Likely layout | Display | Staff | Visitors at once | Build weeks |
|---|---|---|---|---|---|---|
| 9 sq.m | 3 × 3 m | Inline or corner | 7.6 sq.m | 2 | 3 | 3 |
| 18 sq.m | 3 × 6 m | Inline or corner | 15.3 sq.m | 2 | 6 | 3 |
| 36 sq.m | 6 × 6 m | Corner or three-side open | 28.8 sq.m | 4 | 11 | 4 |
| 54 sq.m | 6 × 9 m | Corner or three-side open | 43.2 sq.m | 6 | 17 | 5 |
| 72 sq.m | 6 × 12 m | Three-side open or island | 57.6 sq.m | 8 | 23 | 5 |
Custom stalls typically run ₹9,000–₹18,000 per sq.m for the build; modular and octanorm construction costs less, and an upgraded shell scheme less again. AV, furniture, flooring, transport and taxes are quoted on separate lines.
Designing a stand that works at University & College Campuses, Siliguri
At an education or placement fair the visitor is comparing a row of near-identical stands, so the one legible differentiator — a number, a name, a single clear offer at head height — does more than any amount of finish.
The most common mistake here is treating every wall as equally valuable. One face does most of the work; identify it from the stand plan, spend the budget on it, and treat the rest as support.
Because Siliguri's show calendar leans towards jute, tea and steel, the stands we build at this venue usually need to balance open display against a private corner for commercial conversations.
How a build at university & college campuses runs
01
Read the venue pack
Before anything is drawn we ask for the organiser's pack for your edition: the stand plan with open sides marked, the build-up and dismantle windows, and the rules on height, rigging, fixing and power. At university & college campuses the answer that most often changes a design is the gate, the hour and the academic timetable the build has to fit between.
02
Design to the limits
Design happens against the constraints rather than around them, so modular sections two people can carry and a lighting load a campus board will actually take is a starting condition here rather than a late revision. What you approve in 3D is therefore something that can actually be built in this room.
03
Build and test in the workshop
The stall is fabricated and then stood up in our own workshop: panels numbered, graphics trial-fitted, circuits tested and lamps aimed. Problems get found where there is time to fix them rather than at university & college campuses at midnight.
04
Install, hand over, strike
On site the work is assembly rather than fabrication, which is the whole point of the previous stage. At university & college campuses the install also covers floor protection indoors and reinstatement of grass and paving outside, and the same crew comes back to strike the stand and clear the space.
What else is in Siliguri
There is no dedicated expo hall on the Siliguri list, so every show in the city borrows a room built for something else. That is the single most useful thing to know before designing a stand here: whatever the venue is, it was not designed for exhibitions, and the rules will reflect that.
We also cover 11 venue categories in Siliguri — 5-star hotel ballrooms, convention & banquet halls, open exhibition grounds, mall atriums, university & college campuses, industry association halls, stadium & sports complexes, corporate campus event spaces, industrial estate expo grounds, government exhibition grounds and resort & lawn venues — because most Indian shows outside the top handful of cities happen in a room that was built for something else. Each of those categories has its own access, fixing and power pattern, and each gets its own page.
Every Siliguri venue we cover
Build-up
Build-up, access and approvals in Siliguri
Every Siliguri venue issues its own build-up schedule, power allocation and list of what you may and may not fix to the structure. We read it before fabrication, because a panel that will not fit through the access door is an expensive thing to discover at the venue.
You can take the whole scope or just part of it. Most exhibitors take design and build together and add AV and furniture to the same quote, because the alternative is reconciling three delivery schedules yourself.
What we handle for you
- Organiser drawings, electrical load details and approvals in the format Siliguri organisers ask for
- Design checked against height, rigging, fixing and fire rules before sign-off
- Pre-assembly and electrical testing in the workshop before dispatch
- Transport, installation and an on-site crew inside the build-up window
- Dismantle and clearing the stand inside the dismantle period
Exhibiting elsewhere in West Bengal
Siliguri is one of 5 West Bengal cities on our list, alongside Kolkata, Durgapur, Asansol and Howrah. For an exhibitor doing a state circuit that matters practically: the structure travels, the graphics are reprinted, and nobody has to re-engineer a stand for each stop.
University & college campuses are not unique to Siliguri either: we cover the same category in all 5 of the West Bengal cities on our list, which means the access, fixing and power pattern described above travels with you. A stand built for university & college campuses here is usually re-skinnable for the equivalent venue in the next city rather than rebuildable.
A multi-city programme is mostly a logistics question rather than a design one. One approved drawing set, one set of reusable panels, graphics printed per city and a crew that travels with the stand — that is the whole model, and it is what keeps the per-city cost falling as the programme goes on.
01
Brief
Share stall size, expo and goals. We call within 2 hours.
02
3D Design
Photoreal concepts in 48 hours, revised until perfect.
03
Fabrication
Built and pre-assembled in our own workshops.
04
Install & Show
On-site crew builds, hands over and dismantles.
FAQ
Venue FAQ
Can you build at University & College Campuses, Siliguri?+
Yes. We build at university & college campuses throughout Siliguri, covering design, fabrication, installation and dismantle inside the organiser's window.
What does a stall at University & College Campuses, Siliguri cost?+
Custom stalls typically range from ₹9,000 to ₹18,000 per sq.m depending on size, finishes and AV; modular and octanorm builds cost less. Share your stand size and show dates for an itemised quote.
What are the build-up timings at University & College Campuses, Siliguri?+
Build-up windows are set by the organiser for each show rather than by the venue alone, so we confirm them in writing for your edition and plan the build — including night shifts if needed — around them.
Do you handle approvals for University & College Campuses, Siliguri?+
Yes. We prepare dimensioned drawings, electrical load details and structural documents to the organiser's format, and check the design against the venue's height, rigging and fire rules before fabrication.
Can you provide AV, lighting and furniture at University & College Campuses, Siliguri?+
Yes — LED walls, screens, lighting, furniture, flooring and carpeting can be bundled with the stall build on a single quote.
Who is on site during build-up at University & College Campuses, Siliguri?+
A named project manager and the crew that pre-assembled the stall. They install to the drawing, hand over a working stand and return to dismantle and clear it within the organiser's window.
Can you build a campus fair stand around class timings?+
Yes, and it is usually the only way. Campus builds happen early morning, in the evening or over a weekend, around classes, examinations and security timings. Modular construction and workshop pre-assembly are what let a stand go up in a short window.
Can graphics be reused for next year's campus fair?+
Yes, if the stand is built for it. Frame-and-skin construction lets the structure be stored and re-skinned with new graphics, which is the main reason annual fairs end up cheaper in the second year than the first.
Do you design differently for jute exhibitors here?+
Yes. Siliguri's show calendar is driven by jute, tea, steel, engineering and handicrafts, and the sector decides the fundamentals — how much product has to be on open display, how private the meeting space needs to be, whether the floor has to carry load and whether water, drainage or three-phase power are required. We brief against the sector before the identity.
Can the same stand be used at another West Bengal venue?+
Usually, if it is built for it. We cover 5 West Bengal cities including Siliguri, Kolkata, Durgapur and Asansol, and a frame-and-skin stand can be stored, re-skinned with new graphics and rebuilt at the equivalent venue elsewhere in the state. Say so at design stage, because a reusable stand is detailed differently.
What is the biggest risk at university & college campuses?+
Discovering a constraint after fabrication. Campus power is modest and shared with the building's normal use, so a lighting load designed for an exhibition hall will not run here. That is why we ask for the access route, the fixing rules, the power allocation and the build-up window in writing before anything is cut, rather than treating any of them as a site problem.
More in Siliguri
Other West Bengal cities we cover
Exhibiting soon? Let's build your stall.