Mumbai venue
Stall fabrication at NSCI Dome, Worli
NSCI Dome, Worli is one of Mumbai's key exhibition venues, hosting trade fairs, consumer expos and corporate events throughout the year.
19
Mumbai venues covered
8
Named exhibition venues
11
Venue categories
Tier 1
Maharashtra market
Exhibiting at NSCI Dome, Worli
NSCI Dome, Worli is one of Mumbai's key exhibition venues, hosting trade fairs, consumer expos and corporate events throughout the year. Our crews work to the organiser's build-up window at this venue, pre-assembling in the workshop so site time goes on assembly rather than fabrication.
Two stands of identical size can need completely different engineering depending on the room they go into. Height limits, rigging availability, fixing restrictions, power allocation and build hours all change with the venue, and all of them are settled in writing before fabrication starts.
NSCI Dome, Worli sits in Mumbai's venue mix at the volume end of it — the widest floor and the biggest crowd, with the least permission to touch anything. That position, more than the stall size, is what decides how the stand is engineered: the 19 venues we cover in the city span purpose-built halls, borrowed interiors and open ground, and those are three different trades rather than three versions of one.
Mumbai has the depth of a Tier 1 market — 8 named exhibition venues and 11 venue categories on our list. Depth helps with availability and hurts with scheduling, because every exhibitor in the hall is working to the same window through the same access point.
Building in a stadium or sports complex
Stadium shows put a lot of visitors across a very wide floor, which is good for footfall and hard for logistics. Everything arrives through a tunnel, crosses a protected surface and sits on a base that spreads its weight, and all of it has to be gone again on the organiser's clock.
We treat NSCI Dome, Worli as an indoor stadium or arena for planning purposes and then confirm every figure against the organiser's exhibitor pack for your edition, because rules are issued per show rather than per building.
What changes at NSCI Dome, Worli
| Build input | At a venue of this kind |
|---|---|
| Access route & panel sizes | Service tunnels and player entrances, sized for sports equipment rather than exhibition freight. The tunnel's clear height, not the arena's, sets the tallest piece that can be carried in. |
| Fixing method | Nothing fixed to the structure or the surface. Point loads are spread across load-distributing bases, and tall elements are ballasted and guyed back into the stand itself. |
| Power source | Event distribution rather than house supply, often from a temporary board. The allocation is per stand and worth confirming before any AV is specified. |
| Floor protection | Full protection over the playing surface — interlocking deck or boards under the entire footprint — with wheeled loads confined to protected routes. |
| Build & strike hours | Tight, and dictated by the sporting calendar rather than by the show. Dismantle windows here are frequently shorter than build-up. |
| Weather & environment | An indoor arena is sheltered; the open stands and the surrounding complex are not. A show that spans both is really two builds under one contract. |
Read this as the pattern for indoor stadium or arena, then check it against the organiser's pack. Where the two disagree, the pack wins and the drawing changes before the material does.
How we build for this kind of venue
- Power from event distribution rather than house supply
- Point loads spread across load-distributing bases rather than concentrated
- Nothing fixed to the structure — tall elements ballasted and guyed into the stand
- Wheeled loads confined to protected routes only
- Access through service tunnels sized by their own height, not the arena's
- Tight dismantle windows timed around sporting fixtures
What to ask the organiser about NSCI Dome, Worli
A quote for indoor stadium or arena is an estimate until these answers exist, and a price afterwards. Ask the organiser for them in writing — not because anyone is being difficult, but because the same venue issues different rules for different shows.
Get these in writing before you brief anyone
- Whether anything may be suspended from the roof structure, and through whom
- The permitted point load on the surface, and whether load-spreading bases are mandated
- Which routes wheeled loads may use across the floor
- Who supplies floor protection over the playing surface, and what specification is required
- Tunnel and service-entrance dimensions, including clear height along the whole route
- Whether seating areas and the surrounding complex form part of the show footprint
Who exhibits at Mumbai venues, and what that changes
Automobile, engineering, pharma, textiles and real estate account for most of the exhibiting activity in Mumbai, and the sector is a bigger design input than the brand is. A pharma visitor and a textiles visitor will judge the same 18 sq.m by completely different criteria, so we brief against the sector first and the identity second.
Where a Mumbai show draws from several of those sectors at once, the stand has to serve two briefs in one footprint. Zoning does it — pharma on the open frontage where it needs to be seen, textiles in the pocket behind where it needs to be discussed — and the space plan below is where that gets decided.
Mumbai's sector mix and what each needs from a stand
| Sector | What the stand has to do |
|---|---|
| Pharma | A pharma audience talks in private. A closed meeting corner, lockable sample storage, a wipe-clean dispensing counter and literature capacity matter more than open display area. |
| Textiles | Textile buyers handle everything. Rail and drape capacity, a fold-and-compare table, true-colour lighting, and a lockable store for the sample ranges that leave the stand each day. |
| Real estate | Real estate sells on models and screens. A scale model on a lit plinth, large visuals at eye height, and several seated pockets where a booking conversation can run twenty minutes. |
| Automobile | An automobile and components audience wants to touch the part. Plan a load-rated display platform, a cutaway or turntable at hip height, and circulation wide enough for a crowd around one vehicle. |
| Engineering | An engineering audience reads drawings and specifications, so the stand needs a technical wall, a sample or cutaway to handle, and a table with chairs where a quote can actually be discussed. |
The sectors listed are the ones that drive exhibiting activity across Maharashtra. Where your show draws from more than one of them, the space plan below is where the compromise gets resolved.
Services
What we build at NSCI Dome, Worli
Exhibition Stall Design
Concept-to-3D stall design that stops visitors in the aisle.
Stall Fabrication
In-house carpentry, metal and print for flawless builds.
Custom Exhibition Booths
One-of-a-kind booths built around your brand.
Modular Exhibition Stalls
Reusable, quick-install stalls for frequent exhibitors.
Octanorm & System Stalls
Clean aluminium shell-scheme and system booths.
Double-Decker Stalls
Two-storey stands that double your space.
Pavilion Design
State, industry and association pavilions.
Country Pavilions
National pavilions at Indian and global expos.
Trade Show Booths
High-impact booths for B2B trade shows.
Exhibition Stand Builders
End-to-end stand building with on-site crews.
Event Stage Fabrication
Stages, backdrops and sets for events.
AV & LED Wall Support
LED walls, sound, screens and AV crews.
Stall sizes and lead times for NSCI Dome, Worli
Most stands at a venue like this fall between 9 and 72 sq.m. The table below uses the same formula as our stall planner — storage at 10% of area up to 18 sq.m and 15% above, a meeting corner at 5% unless you are hosting meetings, display taking the remainder — so you can sanity-check a quote against the space you have actually booked.
Lead time is the column exhibitors underestimate. Three weeks is the base for a custom build, four from 24 sq.m and five from 54 sq.m, and those are fabrication weeks after design sign-off rather than from the day you first call. At indoor stadium or arena the build-up window itself is rarely the problem; the approval and fabrication time ahead of it usually is.
Space, staffing and lead time by stall size
| Stall size | Footprint | Likely layout | Display | Staff | Visitors at once | Build weeks |
|---|---|---|---|---|---|---|
| 9 sq.m | 3 × 3 m | Inline or corner | 7.6 sq.m | 2 | 3 | 3 |
| 18 sq.m | 3 × 6 m | Inline or corner | 15.3 sq.m | 2 | 6 | 3 |
| 36 sq.m | 6 × 6 m | Corner or three-side open | 28.8 sq.m | 4 | 11 | 4 |
| 54 sq.m | 6 × 9 m | Corner or three-side open | 43.2 sq.m | 6 | 17 | 5 |
| 72 sq.m | 6 × 12 m | Three-side open or island | 57.6 sq.m | 8 | 23 | 5 |
Custom stalls typically run ₹9,000–₹18,000 per sq.m for the build; modular and octanorm construction costs less, and an upgraded shell scheme less again. AV, furniture, flooring, transport and taxes are quoted on separate lines.
Designing a stand that works at NSCI Dome, Worli
Stadium shows move a lot of visitors across a wide floor in both directions, so plan flow rather than frontage. Keep the open sides facing the main circulation route and accept that the wall side is storage.
The most common mistake here is treating every wall as equally valuable. One face does most of the work; identify it from the stand plan, spend the budget on it, and treat the rest as support.
Because Mumbai's show calendar leans towards automobile, engineering and pharma, the stands we build at this venue usually need to balance open display against a private corner for commercial conversations.
How a build at NSCI Dome, Worli runs
01
Read the venue pack
The job starts with paperwork rather than with a concept. We want the stand plan, the access route, the power allocation and the permitted working hours in writing, and at indoor stadium or arena we pay particular attention to the clear height of the service tunnel and who supplies surface protection.
02
Design to the limits
The concept is then developed inside those limits rather than adjusted to them afterwards. At indoor stadium or arena that means designing for load-spreading bases, full surface protection and pieces that pass a service tunnel from the first sketch instead of retrofitting it to a finished drawing.
03
Build and test in the workshop
Carpentry, metalwork, spray finishing, large-format print and electrical assembly all happen in-house, and the whole stall is assembled once before it ships. That is what turns a short on-site window into enough time.
04
Install, hand over, strike
A named project manager and the crew that pre-assembled the stall install it to the drawing and hand over a working stand. Site care is part of that rather than an afterthought: full protection over the playing surface and wheeled loads kept to protected routes. The same crew returns to dismantle and clear the stand inside the organiser's window.
What else is in Mumbai
We cover 7 other named exhibition venues in Mumbai: Bombay Exhibition Centre (NESCO), Goregaon, Jio World Convention Centre, BKC, MMRDA Grounds, BKC, World Trade Centre Mumbai, Nehru Centre, Worli and CIDCO Exhibition Centre, Vashi, plus 1 more on the city page. By name they break down into 4 purpose-built exhibition and trade centres, 1 convention centre, 1 open ground or maidan and 1 auditorium, hall or cultural centre, and the gap between the easiest and the hardest of those to build in is larger than any gap in stall size.
We also cover 11 venue categories in Mumbai — industry association halls, stadium & sports complexes, corporate campus event spaces, industrial estate expo grounds, government exhibition grounds, resort & lawn venues, 5-star hotel ballrooms, convention & banquet halls, open exhibition grounds, mall atriums and university & college campuses — because most Indian shows outside the top handful of cities happen in a room that was built for something else. Each of those categories has its own access, fixing and power pattern, and each gets its own page.
Named Mumbai venues, read by what each one calls itself
| Venue | Type read from the name | What that implies for a stand |
|---|---|---|
| Bombay Exhibition Centre (NESCO), Goregaon | Purpose-built exhibition or trade centre | In a purpose-built hall you are one of many stands with identical freedoms, so differentiation comes from the things the hall allows and most exhibitors never use: height, light and a clear reason to step in off the aisle.. |
| Jio World Convention Centre, BKC | Convention centre | Banquet halls put stands close together, so the differentiator is usually light rather than size. |
| MMRDA Grounds, BKC | Open ground or maidan | On an open ground your competition is the sky, not the neighbouring stand. |
| World Trade Centre Mumbai | Purpose-built exhibition or trade centre | Hall shows are walked at pace along long aisles, so the stand has to answer what you do from twenty metres and why it matters from two. |
| Nehru Centre, Worli | Auditorium, hall or cultural centre | An auditorium audience is seated for most of the event, which means your stand gets attention in two short windows. |
| CIDCO Exhibition Centre, Vashi | Purpose-built exhibition or trade centre | Hall shows are walked at pace along long aisles, so the stand has to answer what you do from twenty metres and why it matters from two. |
| Bombay Convention & Exhibition Centre | Purpose-built exhibition or trade centre | In a purpose-built hall you are one of many stands with identical freedoms, so differentiation comes from the things the hall allows and most exhibitors never use: height, light and a clear reason to step in off the aisle.. |
A venue's name is a strong hint and not a specification. We confirm height, rigging, fixing, power and hours from the organiser's pack for your edition before design sign-off.
Every Mumbai venue we cover
Build-up
Build-up, access and approvals in Mumbai
Every Mumbai venue issues its own build-up schedule, power allocation and list of what you may and may not fix to the structure. We read it before fabrication, because a panel that will not fit through the access door is an expensive thing to discover at the venue.
You can take the whole scope or just part of it. Most exhibitors take design and build together and add AV and furniture to the same quote, because the alternative is reconciling three delivery schedules yourself.
What we handle for you
- Organiser drawings, electrical load details and approvals in the format Mumbai organisers ask for
- Design checked against height, rigging, fixing and fire rules before sign-off
- Pre-assembly and electrical testing in the workshop before dispatch
- Transport, installation and an on-site crew inside the build-up window
- Dismantle and clearing the stand inside the dismantle period
Exhibiting elsewhere in Maharashtra
Maharashtra is not a one-city exhibition market. We cover 10 cities in the state — Mumbai, Pune, Navi Mumbai, Thane, Nagpur and Nashik, plus 4 more — with the same workshops, crews and project managers, so a programme that runs across several of them runs on one schedule rather than several.
A stand engineered for this venue is rarely a one-show asset. Frame-and-skin construction lets the structure be stored and re-skinned for the next city, which is why the second show in a programme costs materially less than the first.
A multi-city programme is mostly a logistics question rather than a design one. One approved drawing set, one set of reusable panels, graphics printed per city and a crew that travels with the stand — that is the whole model, and it is what keeps the per-city cost falling as the programme goes on.
01
Brief
Share stall size, expo and goals. We call within 2 hours.
02
3D Design
Photoreal concepts in 48 hours, revised until perfect.
03
Fabrication
Built and pre-assembled in our own workshops.
04
Install & Show
On-site crew builds, hands over and dismantles.
FAQ
NSCI Dome, Worli FAQ
Can you build at NSCI Dome, Worli?+
Yes. NSCI Dome, Worli is one of the Mumbai venues our crews work at regularly, covering design, fabrication, installation and dismantle inside the organiser's window.
What does a stall at NSCI Dome, Worli cost?+
Custom stalls typically range from ₹9,000 to ₹18,000 per sq.m depending on size, finishes and AV; modular and octanorm builds cost less. Share your stand size and show dates for an itemised quote.
Do you handle approvals for NSCI Dome, Worli?+
Yes. We prepare dimensioned drawings, electrical load details and structural documents to the organiser's format, and check the design against the venue's height, rigging and fire rules before fabrication.
Can you work to a shell scheme at NSCI Dome, Worli?+
Yes. Where the organiser supplies shell scheme panels we upgrade them with printed fabric or vinyl, raised flooring, spotlights and a branded counter, which lifts the stand a long way at modest cost.
Can you provide AV, lighting and furniture at NSCI Dome, Worli?+
Yes — LED walls, screens, lighting, furniture, flooring and carpeting can be bundled with the stall build on a single quote.
What are the build-up timings at NSCI Dome, Worli?+
Build-up windows are set by the organiser for each show rather than by the venue alone, so we confirm them in writing for your edition and plan the build — including night shifts if needed — around them.
Why is the dismantle window short at a sports complex?+
Because the sporting calendar outranks the show. A fixture following the expo fixes a hard clearance time, so we plan the strike backwards from that time and crew it accordingly rather than treating it as the reverse of build-up.
How is a stadium floor protected during an expo?+
With interlocking deck or protection boards across the entire stand footprint, and wheeled loads kept to protected routes only. Point loads are spread across load-distributing bases so no leg concentrates weight on the surface beneath it.
Do you design differently for automobile exhibitors here?+
Yes. Mumbai's show calendar is driven by automobile, engineering, pharma, textiles and real estate, and the sector decides the fundamentals — how much product has to be on open display, how private the meeting space needs to be, whether the floor has to carry load and whether water, drainage or three-phase power are required. We brief against the sector before the identity.
Can the same stand be used at another Maharashtra venue?+
Usually, if it is built for it. We cover 10 Maharashtra cities including Mumbai, Pune, Navi Mumbai and Thane, and a frame-and-skin stand can be stored, re-skinned with new graphics and rebuilt at the equivalent venue elsewhere in the state. Say so at design stage, because a reusable stand is detailed differently.
What is the biggest risk at indoor stadium or arena?+
Discovering a constraint after fabrication. The service tunnel rather than the arena limits what can be carried in, and a piece that will not pass it never reaches the floor at all. That is why we ask for the access route, the fixing rules, the power allocation and the build-up window in writing before anything is cut, rather than treating any of them as a site problem.
More in Mumbai
Other Maharashtra cities we cover
Exhibiting soon? Let's build your stall.