Kolkata venue
Stall fabrication at Open Exhibition Grounds, Kolkata
Open grounds where hangar-style German-tent exhibitions and trade fairs are set up.
17
Kolkata venues covered
6
Named exhibition venues
11
Venue categories
Tier 1
West Bengal market
Exhibiting at Open Exhibition Grounds, Kolkata
Open grounds where hangar-style German-tent exhibitions and trade fairs are set up. We design, fabricate, install and dismantle stalls here, with the organiser drawings and approvals prepared as part of the project rather than quoted as an extra.
Two stands of identical size can need completely different engineering depending on the room they go into. Height limits, rigging availability, fixing restrictions, power allocation and build hours all change with the venue, and all of them are settled in writing before fabrication starts.
Of the 17 Kolkata venues we cover, this one occupies the most open end of it — no walls, no ceiling, no fixed limits, and no shelter either. Exhibitors tend to compare venues on footfall and cost; builders compare them on access, fixing and power, and on that measure the gap between the extremes of the Kolkata list is very wide.
Kolkata has the depth of a Tier 1 market — 6 named exhibition venues and 11 venue categories on our list. Depth helps with availability and hurts with scheduling, because every exhibitor in the hall is working to the same window through the same access point.
Building on an open exhibition ground
An open ground is the most flexible and the most exposed option in any city. There is no door to limit panel size and usually no ceiling to limit height, because vehicles can reach the stand itself — but weather, dust, ground level and generator power all have to be designed in rather than assumed, and a hangar or German tent normally sits over the top of the whole thing.
Open exhibition grounds vary from one address to the next even inside Kolkata, so the figures below are the pattern rather than the contract. The organiser's pack for your show is what we actually design to.
What changes at open exhibition grounds
| Build input | At open exhibition grounds |
|---|---|
| Access route & panel sizes | Vehicles usually reach the stand itself, so panel size is limited by the truck and the crew rather than by a door. That is the one real structural advantage an open ground gives a builder. |
| Fixing method | Pegs, ballast and ground anchors, plus fixings into the hangar or tent frame where the organiser permits them. Tall elements are triangulated because there is nothing solid to lean against. |
| Power source | Generator supply with its own distribution and a backup path. Cable runs are long, so voltage drop, protected routing and crossing points across walkways are designed rather than discovered. |
| Floor protection | Raised platform flooring to level uneven ground, keep dust down and give cables a route. Underneath the platform, drainage matters as much as levelling does. |
| Build & strike hours | A longer build-up window than an indoor hall, because tenting, flooring and power all precede the stand. Daylight working is the norm and dust is continuous. |
| Weather & environment | The governing constraint. Rain, wind, heat and dust are all designed for — sealed edges, covered junctions, wind loading on anything tall, and no graphic that cannot take a shower. |
These six are the ones that change the stand rather than the drawing. Confirm them for your edition with the organiser and we will design to the answers; where an answer is unavailable we design to the conservative assumption and revise once it arrives.
How we build for this kind of venue
- Wind loading accounted for on every tall, hanging or fabric element
- Generator power with its own distribution and a backup path
- Edge sealing and covered electrical junctions as standard on an exposed site
- Raised platform flooring to level the ground, seal out dust and carry cable runs
- Panels sized by the truck and the crew rather than by a door
- Weather protection and water ingress planned for, not improvised on the day
What to ask the organiser about open exhibition grounds
Send the organiser this list before you commission anything. Each answer removes a contingency from the quote, and at open exhibition grounds two or three of them change the structure rather than the finish.
Get these in writing before you brief anyone
- Wind-loading limits on tall or hanging elements, and whether any are barred outright
- The ground surface — levelled earth, hardstanding or turf — and whether pegging is permitted
- Whether power is generator or mains, the allocation per stand, and the distance to the connection point
- Overnight security arrangements on an open site
- Vehicle access to the stand itself, and for how long a vehicle may remain
- Who is responsible for drainage and for standing water during the show
Who exhibits at Kolkata venues, and what that changes
The sector mix in Kolkata is jute, tea, steel, engineering and handicrafts, and each of those brings its own non-negotiables onto a stand. The table below is what we design against at open exhibition grounds before a single visual is drawn, because most of these requirements are structural or electrical rather than decorative.
Mixed-sector shows are the harder case. Jute and tea visitors want opposite things from the same footprint, and the resolution is zoning rather than compromise: open display on the aisle face, a closed or semi-closed corner behind it, and storage that keeps the difference invisible.
Kolkata's sector mix and what each needs from a stand
| Sector | What the stand has to do |
|---|---|
| Jute | Jute exhibitors show bags, fabric and bulk product. Open stacking, a handling surface, and a packing counter for buyers who will take samples away with them. |
| Tea | Tea selling is tasting. A serviced counter with water, power for an urn, drainage, a clean sampling surface, and a seated corner for a buyer tasting through a range. |
| Steel | Steel exhibitors bring heavy samples — sections, coil, plate. Load-rated plinths, a spread footprint beneath them, a technical wall, and a closed room for tonnage conversations. |
| Engineering | An engineering audience reads drawings and specifications, so the stand needs a technical wall, a sample or cutaway to handle, and a table with chairs where a quote can actually be discussed. |
| Handicrafts | Handicraft stands sell density. Open shelving, sightlines into the stand rather than a counter across the front, and light aimed at the object instead of the ceiling. |
The sectors listed are the ones that drive exhibiting activity across West Bengal. Where your show draws from more than one of them, the space plan below is where the compromise gets resolved.
Services
What we build at Open Exhibition Grounds, Kolkata
Exhibition Stall Design
Concept-to-3D stall design that stops visitors in the aisle.
Stall Fabrication
In-house carpentry, metal and print for flawless builds.
Custom Exhibition Booths
One-of-a-kind booths built around your brand.
Modular Exhibition Stalls
Reusable, quick-install stalls for frequent exhibitors.
Octanorm & System Stalls
Clean aluminium shell-scheme and system booths.
Double-Decker Stalls
Two-storey stands that double your space.
Pavilion Design
State, industry and association pavilions.
Country Pavilions
National pavilions at Indian and global expos.
Trade Show Booths
High-impact booths for B2B trade shows.
Exhibition Stand Builders
End-to-end stand building with on-site crews.
Event Stage Fabrication
Stages, backdrops and sets for events.
AV & LED Wall Support
LED walls, sound, screens and AV crews.
Stall sizes and lead times for Open Exhibition Grounds, Kolkata
Most stands at a venue like this fall between 9 and 72 sq.m. The table below uses the same formula as our stall planner — storage at 10% of area up to 18 sq.m and 15% above, a meeting corner at 5% unless you are hosting meetings, display taking the remainder — so you can sanity-check a quote against the space you have actually booked.
The figures are the same ones our stall planner uses, so a quote can be checked against them line by line: storage at 10% of the area up to 18 sq.m and 15% above it, a meeting corner at 5% unless you are actually hosting meetings, display taking whatever remains, one staff member per 9 sq.m, and the number of visitors who can stand in the stall at once coming out at display area divided by 2.5.
Space, staffing and lead time by stall size
| Stall size | Footprint | Likely layout | Display | Staff | Visitors at once | Build weeks |
|---|---|---|---|---|---|---|
| 9 sq.m | 3 × 3 m | Inline or corner | 7.6 sq.m | 2 | 3 | 3 |
| 18 sq.m | 3 × 6 m | Inline or corner | 15.3 sq.m | 2 | 6 | 3 |
| 36 sq.m | 6 × 6 m | Corner or three-side open | 28.8 sq.m | 4 | 11 | 4 |
| 54 sq.m | 6 × 9 m | Corner or three-side open | 43.2 sq.m | 6 | 17 | 5 |
| 72 sq.m | 6 × 12 m | Three-side open or island | 57.6 sq.m | 8 | 23 | 5 |
Custom stalls typically run ₹9,000–₹18,000 per sq.m for the build; modular and octanorm construction costs less, and an upgraded shell scheme less again. AV, furniture, flooring, transport and taxes are quoted on separate lines.
Designing a stand that works at Open Exhibition Grounds, Kolkata
Open-ground visitors arrive hot, dusty and already tired of walking. A shaded standing area with somewhere to put a bag converts better than another graphic wall, and it costs less.
Visitors decide whether to enter from several metres away, so the stand has to answer "what do you do?" before it answers anything else. One legible line at eye height does more than a wall of product shots.
The buyers at this venue tend to come from jute, tea and steel. That shapes the brief more than the aesthetics do — a jute visitor is looking for evidence, not atmosphere.
How a build at open exhibition grounds runs
01
Read the venue pack
The job starts with paperwork rather than with a concept. We want the stand plan, the access route, the power allocation and the permitted working hours in writing, and at open exhibition grounds we pay particular attention to whether tenting and flooring are provided by the organiser, and when they will be finished.
02
Design to the limits
Design happens against the constraints rather than around them, so platform flooring, sealed edges, wind loading on tall elements and generator distribution is a starting condition here rather than a late revision. What you approve in 3D is therefore something that can actually be built in this room.
03
Build and test in the workshop
The stall is fabricated and then stood up in our own workshop: panels numbered, graphics trial-fitted, circuits tested and lamps aimed. Problems get found where there is time to fix them rather than at open exhibition grounds at midnight.
04
Install, hand over, strike
A named project manager and the crew that pre-assembled the stall install it to the drawing and hand over a working stand. Site care is part of that rather than an afterthought: levelling, dust sealing at the platform edges and covered electrical junctions. The same crew returns to dismantle and clear the stand inside the organiser's window.
What else is in Kolkata
Kolkata gives you more than one kind of room. Alongside this page we cover 6 named exhibition venues in the city — Biswa Bangla Mela Prangan, Biswa Bangla Convention Centre, Science City Convention Centre, Milan Mela Prangan, Netaji Indoor Stadium and Central Park Salt Lake. Read by what each one calls itself, that list comprises 2 purpose-built exhibition and trade centres, 2 convention centres, 1 hotel ballroom or hotel convention hall and 1 open ground or maidan: 4 different build specifications inside one city.
Underneath the named venues sit the 11 venue categories we cover in every city, Kolkata included: mall atriums, university & college campuses, industry association halls, stadium & sports complexes, corporate campus event spaces, industrial estate expo grounds, government exhibition grounds, resort & lawn venues, 5-star hotel ballrooms, convention & banquet halls and open exhibition grounds. A large share of exhibiting activity in India happens in those rooms rather than in exhibition halls, which is why they get their own pages rather than a footnote.
Named Kolkata venues, read by what each one calls itself
| Venue | Type read from the name | What that implies for a stand |
|---|---|---|
| Biswa Bangla Mela Prangan | Purpose-built exhibition or trade centre | In a purpose-built hall you are one of many stands with identical freedoms, so differentiation comes from the things the hall allows and most exhibitors never use: height, light and a clear reason to step in off the aisle.. |
| Biswa Bangla Convention Centre | Convention centre | Banquet halls put stands close together, so the differentiator is usually light rather than size. |
| Science City Convention Centre | Convention centre | A pillar-less hall gives you a long sightline down the aisle, which makes the face that reads from thirty metres away worth more than the one a visitor sees standing in front of you. |
| Milan Mela Prangan | Purpose-built exhibition or trade centre | Hall shows are walked at pace along long aisles, so the stand has to answer what you do from twenty metres and why it matters from two. |
| Netaji Indoor Stadium | Hotel ballroom or hotel convention hall | In a ballroom the room is already handsome, so a stand that competes with the chandeliers loses. |
| Central Park Salt Lake | Open ground or maidan | Open-ground visitors arrive hot, dusty and already tired of walking. |
A venue's name is a strong hint and not a specification. We confirm height, rigging, fixing, power and hours from the organiser's pack for your edition before design sign-off.
Every Kolkata venue we cover
Build-up
Build-up, access and approvals in Kolkata
The two things that cost exhibitors time in Kolkata are materials arriving loose and electricals being tested for the first time on site. We ship pre-assembled, pre-wired and pre-fitted, which is why a tight build-up window is normally enough.
Everything the stand needs — structure, print, lighting, flooring, furniture, AV and the crew to install and strike it — can be bundled into a single itemised quote with one project manager behind it.
What we handle for you
- Organiser drawings, electrical load details and approvals in the format Kolkata organisers ask for
- Design checked against height, rigging, fixing and fire rules before sign-off
- Pre-assembly and electrical testing in the workshop before dispatch
- Transport, installation and an on-site crew inside the build-up window
- Dismantle and clearing the stand inside the dismantle period
Exhibiting elsewhere in West Bengal
West Bengal is not a one-city exhibition market. We cover 5 cities in the state — Kolkata, Siliguri, Durgapur, Asansol and Howrah — with the same workshops, crews and project managers, so a programme that runs across several of them runs on one schedule rather than several.
Because we cover open exhibition grounds in all 5 West Bengal cities on our list, a stand designed for this venue type is designed for the state. The structure, the fixing method and the power assumptions carry over; only the footprint and the graphics change.
If this venue is one stop on a programme, say so at design stage. A stand drawn to be reused is drawn differently — demountable joints, numbered panels, graphics on replaceable skins and a storage footprint that fits a standard crate — and retrofitting that later costs more than building it in.
01
Brief
Share stall size, expo and goals. We call within 2 hours.
02
3D Design
Photoreal concepts in 48 hours, revised until perfect.
03
Fabrication
Built and pre-assembled in our own workshops.
04
Install & Show
On-site crew builds, hands over and dismantles.
FAQ
Venue FAQ
Can you build at Open Exhibition Grounds, Kolkata?+
Yes. We build at open exhibition grounds throughout Kolkata, covering design, fabrication, installation and dismantle inside the organiser's window.
What does a stall at Open Exhibition Grounds, Kolkata cost?+
Custom stalls typically range from ₹9,000 to ₹18,000 per sq.m depending on size, finishes and AV; modular and octanorm builds cost less. Share your stand size and show dates for an itemised quote.
How early should I book for a show at Open Exhibition Grounds, Kolkata?+
Four to six weeks ahead for a custom stall and eight or more for a double-decker or pavilion. Urgent builds in seven to ten days are possible with a simplified design.
Can you work to a shell scheme at Open Exhibition Grounds, Kolkata?+
Yes. Where the organiser supplies shell scheme panels we upgrade them with printed fabric or vinyl, raised flooring, spotlights and a branded counter, which lifts the stand a long way at modest cost.
Do you handle approvals for Open Exhibition Grounds, Kolkata?+
Yes. We prepare dimensioned drawings, electrical load details and structural documents to the organiser's format, and check the design against the venue's height, rigging and fire rules before fabrication.
Who is on site during build-up at Open Exhibition Grounds, Kolkata?+
A named project manager and the crew that pre-assembled the stall. They install to the drawing, hand over a working stand and return to dismantle and clear it within the organiser's window.
Is build-up longer on an open ground?+
Yes. Tenting, flooring and power distribution all have to be finished before stand building starts, so the organiser's build-up period is longer than an indoor hall's and the sequence is published. We plan our arrival against that sequence rather than against the first available day.
How is power supplied on an open exhibition ground?+
Usually by generator, with distribution run out to the stands and a backup path for critical loads. We confirm the allocation and the distance to the connection point in advance, because long cable runs change both the cable specification and the cost.
Do you design differently for jute exhibitors here?+
Yes. Kolkata's show calendar is driven by jute, tea, steel, engineering and handicrafts, and the sector decides the fundamentals — how much product has to be on open display, how private the meeting space needs to be, whether the floor has to carry load and whether water, drainage or three-phase power are required. We brief against the sector before the identity.
Can the same stand be used at another West Bengal venue?+
Usually, if it is built for it. We cover 5 West Bengal cities including Kolkata, Siliguri, Durgapur and Asansol, and a frame-and-skin stand can be stored, re-skinned with new graphics and rebuilt at the equivalent venue elsewhere in the state. Say so at design stage, because a reusable stand is detailed differently.
What is the biggest risk at open exhibition grounds?+
Discovering a constraint after fabrication. Flooring, tenting and generator power all precede your stand on an open ground, so a crew planned in for the first available day arrives before the site is ready for them. That is why we ask for the access route, the fixing rules, the power allocation and the build-up window in writing before anything is cut, rather than treating any of them as a site problem.
More in Kolkata
Other West Bengal cities we cover
Exhibiting soon? Let's build your stall.