Mohali venue
Stall fabrication at Open Exhibition Grounds, Mohali
Open grounds where hangar-style German-tent exhibitions and trade fairs are set up.
11
Mohali venues covered
0
Named exhibition venues
11
Venue categories
Tier 2
Punjab market
Exhibiting at Open Exhibition Grounds, Mohali
Open grounds where hangar-style German-tent exhibitions and trade fairs are set up. We design, fabricate, install and dismantle stalls here, with the organiser drawings and approvals prepared as part of the project rather than quoted as an extra.
The reason venue matters more than it looks is that it sets the limits the design has to obey — ceiling height, rigging, what you may fix to, how much power you are allocated and when you are allowed to work. We confirm those for your specific show before anything is cut, because a panel that will not pass the access door is an expensive discovery to make on site.
Open Exhibition Grounds, Mohali sits in Mohali's venue mix at the most open end of it — no walls, no ceiling, no fixed limits, and no shelter either. That position, more than the stall size, is what decides how the stand is engineered: the 11 venues we cover in the city span purpose-built halls, borrowed interiors and open ground, and those are three different trades rather than three versions of one.
Mohali is a growing exhibition market rather than a mature one, and the venues reflect that: 11 venue categories and no single purpose-built exhibition centre on our list. Rooms are shared with other kinds of event, so the paperwork and the hours come from whoever owns the room rather than from an exhibition operator.
Building on an open exhibition ground
Open grounds give a builder the freedom indoor venues cannot: large panels delivered to the stand, height limited by the tent rather than a slab-to-soffit figure, and a vehicle alongside the build for as long as it is needed. The trade is that the specification has to survive rain, wind, heat and dust for the length of the show.
Within Mohali the specific room still matters: two open exhibition grounds in the same city can differ on clear height, access and power. We confirm those in writing for your edition rather than carrying an assumption from the last build.
What changes at open exhibition grounds
| Build input | At open exhibition grounds |
|---|---|
| Access route & panel sizes | Vehicles usually reach the stand itself, so panel size is limited by the truck and the crew rather than by a door. That is the one real structural advantage an open ground gives a builder. |
| Fixing method | Pegs, ballast and ground anchors, plus fixings into the hangar or tent frame where the organiser permits them. Tall elements are triangulated because there is nothing solid to lean against. |
| Power source | Generator supply with its own distribution and a backup path. Cable runs are long, so voltage drop, protected routing and crossing points across walkways are designed rather than discovered. |
| Floor protection | Raised platform flooring to level uneven ground, keep dust down and give cables a route. Underneath the platform, drainage matters as much as levelling does. |
| Build & strike hours | A longer build-up window than an indoor hall, because tenting, flooring and power all precede the stand. Daylight working is the norm and dust is continuous. |
| Weather & environment | The governing constraint. Rain, wind, heat and dust are all designed for — sealed edges, covered junctions, wind loading on anything tall, and no graphic that cannot take a shower. |
These six are the ones that change the stand rather than the drawing. Confirm them for your edition with the organiser and we will design to the answers; where an answer is unavailable we design to the conservative assumption and revise once it arrives.
How we build for this kind of venue
- Panels sized by the truck and the crew rather than by a door
- Wind loading accounted for on every tall, hanging or fabric element
- A longer build-up window because tenting, flooring and power precede the stand
- Generator power with its own distribution and a backup path
- Raised platform flooring to level the ground, seal out dust and carry cable runs
- Edge sealing and covered electrical junctions as standard on an exposed site
What to ask the organiser about open exhibition grounds
Most of what goes wrong at open exhibition grounds goes wrong because a question was not asked early. These are the ones worth asking before you brief a designer, let alone a fabricator.
Get these in writing before you brief anyone
- The ground surface — levelled earth, hardstanding or turf — and whether pegging is permitted
- Who is responsible for drainage and for standing water during the show
- The build-up sequence, since flooring and tenting have to be finished before stands begin
- Whether tenting or a hangar is provided by the organiser, and the clear height under it
- Wind-loading limits on tall or hanging elements, and whether any are barred outright
- Vehicle access to the stand itself, and for how long a vehicle may remain
Who exhibits at Mohali venues, and what that changes
The sector mix in Mohali is hosiery, agri machinery, bicycles, food processing and sports goods, and each of those brings its own non-negotiables onto a stand. The table below is what we design against at open exhibition grounds before a single visual is drawn, because most of these requirements are structural or electrical rather than decorative.
Most Mohali exhibitors are selling to more than one of those audiences, which is an argument for a layout rather than a style. Give the food processing audience the frontage and the sports goods audience the back corner, and the stand stops trying to be two things in the same square metre.
Mohali's sector mix and what each needs from a stand
| Sector | What the stand has to do |
|---|---|
| Food processing | Food processing mixes machinery with product, so you need a load-rated platform, a hygienic demo surface, a water point and a safe line between the visitor and a moving part. |
| Sports goods | Sports goods need a trial area and height for racked product. Protect the floor under any activity, and keep the demo zone from spilling into the aisle. |
| Hosiery | Hosiery and apparel buyers want range and hand-feel. Rail capacity, a handling table, a mirror and a lockable stock area are worth more than a feature wall. |
| Agri machinery | Agri machinery needs a load-rated platform, a route onto it that takes wheels or tracks, a marked safe viewing line, and a power feed sized for the heaviest motor on the stand. |
| Bicycles | Bicycles need floor area and height — wall mounts, a hanging rack and a clear test strip or roller. None of that works pressed against a back wall. |
The sectors listed are the ones that drive exhibiting activity across Punjab. Where your show draws from more than one of them, the space plan below is where the compromise gets resolved.
Services
What we build at Open Exhibition Grounds, Mohali
Exhibition Stall Design
Concept-to-3D stall design that stops visitors in the aisle.
Stall Fabrication
In-house carpentry, metal and print for flawless builds.
Custom Exhibition Booths
One-of-a-kind booths built around your brand.
Modular Exhibition Stalls
Reusable, quick-install stalls for frequent exhibitors.
Octanorm & System Stalls
Clean aluminium shell-scheme and system booths.
Double-Decker Stalls
Two-storey stands that double your space.
Pavilion Design
State, industry and association pavilions.
Country Pavilions
National pavilions at Indian and global expos.
Trade Show Booths
High-impact booths for B2B trade shows.
Exhibition Stand Builders
End-to-end stand building with on-site crews.
Event Stage Fabrication
Stages, backdrops and sets for events.
AV & LED Wall Support
LED walls, sound, screens and AV crews.
Stall sizes and lead times for Open Exhibition Grounds, Mohali
Most stands at a venue like this fall between 9 and 72 sq.m. The table below uses the same formula as our stall planner — storage at 10% of area up to 18 sq.m and 15% above, a meeting corner at 5% unless you are hosting meetings, display taking the remainder — so you can sanity-check a quote against the space you have actually booked.
The figures are the same ones our stall planner uses, so a quote can be checked against them line by line: storage at 10% of the area up to 18 sq.m and 15% above it, a meeting corner at 5% unless you are actually hosting meetings, display taking whatever remains, one staff member per 9 sq.m, and the number of visitors who can stand in the stall at once coming out at display area divided by 2.5.
Space, staffing and lead time by stall size
| Stall size | Footprint | Likely layout | Display | Staff | Visitors at once | Build weeks |
|---|---|---|---|---|---|---|
| 9 sq.m | 3 × 3 m | Inline or corner | 7.6 sq.m | 2 | 3 | 3 |
| 18 sq.m | 3 × 6 m | Inline or corner | 15.3 sq.m | 2 | 6 | 3 |
| 36 sq.m | 6 × 6 m | Corner or three-side open | 28.8 sq.m | 4 | 11 | 4 |
| 54 sq.m | 6 × 9 m | Corner or three-side open | 43.2 sq.m | 6 | 17 | 5 |
| 72 sq.m | 6 × 12 m | Three-side open or island | 57.6 sq.m | 8 | 23 | 5 |
Custom stalls typically run ₹9,000–₹18,000 per sq.m for the build; modular and octanorm construction costs less, and an upgraded shell scheme less again. AV, furniture, flooring, transport and taxes are quoted on separate lines.
Designing a stand that works at Open Exhibition Grounds, Mohali
On an open ground your competition is the sky, not the neighbouring stand. Height, a roof line of your own and lighting that still works at dusk are what make a stand findable from the far side of the ground.
Plan the stand around one decision: what do you want a visitor to do in the ninety seconds they will give you? Everything else — the graphic hierarchy, where staff stand, where the product sits — follows from answering that honestly.
Exhibitors here come largely from hosiery, agri machinery and bicycles, and a hosiery audience has specific expectations: product visible, specification available, and somewhere to talk without shouting. We design for that rather than applying a generic layout.
How a build at open exhibition grounds runs
01
Read the venue pack
Before anything is drawn we ask for the organiser's pack for your edition: the stand plan with open sides marked, the build-up and dismantle windows, and the rules on height, rigging, fixing and power. At open exhibition grounds the answer that most often changes a design is whether tenting and flooring are provided by the organiser, and when they will be finished.
02
Design to the limits
The concept is then developed inside those limits rather than adjusted to them afterwards. At open exhibition grounds that means designing for platform flooring, sealed edges, wind loading on tall elements and generator distribution from the first sketch instead of retrofitting it to a finished drawing.
03
Build and test in the workshop
Carpentry, metalwork, spray finishing, large-format print and electrical assembly all happen in-house, and the whole stall is assembled once before it ships. That is what turns a short on-site window into enough time.
04
Install, hand over, strike
A named project manager and the crew that pre-assembled the stall install it to the drawing and hand over a working stand. Site care is part of that rather than an afterthought: levelling, dust sealing at the platform edges and covered electrical junctions. The same crew returns to dismantle and clear the stand inside the organiser's window.
What else is in Mohali
There is no dedicated expo hall on the Mohali list, so every show in the city borrows a room built for something else. That is the single most useful thing to know before designing a stand here: whatever the venue is, it was not designed for exhibitions, and the rules will reflect that.
Underneath the named venues sit the 11 venue categories we cover in every city, Mohali included: open exhibition grounds, mall atriums, university & college campuses, industry association halls, stadium & sports complexes, corporate campus event spaces, industrial estate expo grounds, government exhibition grounds, resort & lawn venues, 5-star hotel ballrooms and convention & banquet halls. A large share of exhibiting activity in India happens in those rooms rather than in exhibition halls, which is why they get their own pages rather than a footnote.
Every Mohali venue we cover
Build-up
Build-up, access and approvals in Mohali
The two things that cost exhibitors time in Mohali are materials arriving loose and electricals being tested for the first time on site. We ship pre-assembled, pre-wired and pre-fitted, which is why a tight build-up window is normally enough.
Design, fabrication, graphics, lighting, flooring, furniture, installation and dismantle can all sit on one quote, which is usually cheaper than sourcing them separately once you account for three margins and the coordination time.
What we handle for you
- Organiser drawings, electrical load details and approvals in the format Mohali organisers ask for
- Design checked against height, rigging, fixing and fire rules before sign-off
- Pre-assembly and electrical testing in the workshop before dispatch
- Transport, installation and an on-site crew inside the build-up window
- Dismantle and clearing the stand inside the dismantle period
Exhibiting elsewhere in Punjab
Punjab is not a one-city exhibition market. We cover 6 cities in the state — Mohali, Ludhiana, Amritsar, Jalandhar, Bathinda and Patiala — with the same workshops, crews and project managers, so a programme that runs across several of them runs on one schedule rather than several.
Because we cover open exhibition grounds in all 6 Punjab cities on our list, a stand designed for this venue type is designed for the state. The structure, the fixing method and the power assumptions carry over; only the footprint and the graphics change.
If this venue is one stop on a programme, say so at design stage. A stand drawn to be reused is drawn differently — demountable joints, numbered panels, graphics on replaceable skins and a storage footprint that fits a standard crate — and retrofitting that later costs more than building it in.
01
Brief
Share stall size, expo and goals. We call within 2 hours.
02
3D Design
Photoreal concepts in 48 hours, revised until perfect.
03
Fabrication
Built and pre-assembled in our own workshops.
04
Install & Show
On-site crew builds, hands over and dismantles.
FAQ
Venue FAQ
Can you build at Open Exhibition Grounds, Mohali?+
Yes. We build at open exhibition grounds throughout Mohali, covering design, fabrication, installation and dismantle inside the organiser's window.
What does a stall at Open Exhibition Grounds, Mohali cost?+
Custom stalls typically range from ₹9,000 to ₹18,000 per sq.m depending on size, finishes and AV; modular and octanorm builds cost less. Share your stand size and show dates for an itemised quote.
How early should I book for a show at Open Exhibition Grounds, Mohali?+
Four to six weeks ahead for a custom stall and eight or more for a double-decker or pavilion. Urgent builds in seven to ten days are possible with a simplified design.
What are the build-up timings at Open Exhibition Grounds, Mohali?+
Build-up windows are set by the organiser for each show rather than by the venue alone, so we confirm them in writing for your edition and plan the build — including night shifts if needed — around them.
Can you work to a shell scheme at Open Exhibition Grounds, Mohali?+
Yes. Where the organiser supplies shell scheme panels we upgrade them with printed fabric or vinyl, raised flooring, spotlights and a branded counter, which lifts the stand a long way at modest cost.
Who is on site during build-up at Open Exhibition Grounds, Mohali?+
A named project manager and the crew that pre-assembled the stall. They install to the drawing, hand over a working stand and return to dismantle and clear it within the organiser's window.
Is build-up longer on an open ground?+
Yes. Tenting, flooring and power distribution all have to be finished before stand building starts, so the organiser's build-up period is longer than an indoor hall's and the sequence is published. We plan our arrival against that sequence rather than against the first available day.
How is power supplied on an open exhibition ground?+
Usually by generator, with distribution run out to the stands and a backup path for critical loads. We confirm the allocation and the distance to the connection point in advance, because long cable runs change both the cable specification and the cost.
Do you design differently for hosiery exhibitors here?+
Yes. Mohali's show calendar is driven by hosiery, agri machinery, bicycles, food processing and sports goods, and the sector decides the fundamentals — how much product has to be on open display, how private the meeting space needs to be, whether the floor has to carry load and whether water, drainage or three-phase power are required. We brief against the sector before the identity.
Can the same stand be used at another Punjab venue?+
Usually, if it is built for it. We cover 6 Punjab cities including Mohali, Ludhiana, Amritsar and Jalandhar, and a frame-and-skin stand can be stored, re-skinned with new graphics and rebuilt at the equivalent venue elsewhere in the state. Say so at design stage, because a reusable stand is detailed differently.
What is the biggest risk at open exhibition grounds?+
Discovering a constraint after fabrication. Flooring, tenting and generator power all precede your stand on an open ground, so a crew planned in for the first available day arrives before the site is ready for them. That is why we ask for the access route, the fixing rules, the power allocation and the build-up window in writing before anything is cut, rather than treating any of them as a site problem.
More in Mohali
Other Punjab cities we cover
Exhibiting soon? Let's build your stall.