Kochi venue
Stall fabrication at Adlux International Convention & Exhibition Centre
Adlux International Convention & Exhibition Centre is one of Kochi's key exhibition venues, hosting trade fairs, consumer expos and corporate events throughout the year.
15
Kochi venues covered
4
Named exhibition venues
11
Venue categories
Tier 2
Kerala market
Exhibiting at Adlux International Convention & Exhibition Centre
Adlux International Convention & Exhibition Centre is one of Kochi's key exhibition venues, hosting trade fairs, consumer expos and corporate events throughout the year. We design, fabricate, install and dismantle stalls here, with the organiser drawings and approvals prepared as part of the project rather than quoted as an extra.
Two stands of identical size can need completely different engineering depending on the room they go into. Height limits, rigging availability, fixing restrictions, power allocation and build hours all change with the venue, and all of them are settled in writing before fabrication starts.
Of the 15 Kochi venues we cover, this one occupies the purpose-built end of it — the fewest constraints and therefore the most competition for attention. Exhibitors tend to compare venues on footfall and cost; builders compare them on access, fixing and power, and on that measure the gap between the extremes of the Kochi list is very wide.
Kochi is a Tier 2 exhibition market in Kerala, which changes the venue question rather than the build quality. We cover 4 named venues here, plus 11 venue categories, so shows share their rooms with weddings, conferences and civic events and your build has to fit around bookings made before yours.
Building in a purpose-built exhibition hall
In a purpose-built hall most of the usual constraints disappear and a different one takes their place: everyone else has the same freedoms you do. Rigging may be available from roof points, height allowances are generous, night working is permitted and the slab takes whatever you put on it — so differentiation has to be earned rather than inherited from the room.
Adlux International Convention & Exhibition Centre is read here as a purpose-built exhibition or trade centre, which is how we plan a build until the organiser's pack for your edition says otherwise. The pack is what settles height, rigging, fixing, power and hours for a specific show, and the same building can issue different rules for two shows in the same month.
What changes at Adlux International Convention & Exhibition Centre
| Build input | At a venue of this kind |
|---|---|
| Access route & panel sizes | A dedicated loading bay, dock-height access and a hall door sized for exhibition freight. This is the one venue type where the stand, not the door, sets the panel size. |
| Fixing method | Freestanding on the hall floor, with rigging from roof points where the organiser offers it. Fixing into the floor slab is normally barred even here, so weight still goes into the base. |
| Power source | A metered allocation ordered through the organiser, usually with single and three-phase options. Order the load you need at booking, because upgrading on site is slow and expensive. |
| Floor protection | A slab built for the job, so protection is about your own finish rather than the building's. Raised platform flooring becomes a design choice here instead of a necessity. |
| Build & strike hours | A published build-up and dismantle schedule, often across several days, with a hard deadline for aisle clearance. Night working is common and normally permitted. |
| Weather & environment | Enclosed, but the hall doors stand open through build-up, so expect dust and heat while building and a controlled environment once the show opens. |
Read this as the pattern for purpose-built exhibition or trade centre, then check it against the organiser's pack. Where the two disagree, the pack wins and the drawing changes before the material does.
How we build for this kind of venue
- Rigging from roof points where the organiser offers it, ordered in advance
- Dust and heat during build-up while the hall doors stand open
- Height allowances confirmed against the organiser's rulebook before sign-off
- Dock-height loading access, so panel size is set by the design rather than a door
- Published build-up and dismantle schedules, with night working normally permitted
- A hard deadline for aisle clearance that the whole programme is planned around
What to ask the organiser about Adlux International Convention & Exhibition Centre
A quote for purpose-built exhibition or trade centre is an estimate until these answers exist, and a price afterwards. Ask the organiser for them in writing — not because anyone is being difficult, but because the same venue issues different rules for different shows.
Get these in writing before you brief anyone
- The published build-up and dismantle schedule, including the aisle clearance deadline
- Floor-loading limits, if anything heavy or two-storey is planned
- What the shell scheme, if any, includes — and what it does not
- The maximum build height for your stand type, and the setback rules at the edges
- Whether the organiser's drawing approval has a submission deadline
- The power allocation you have ordered, the phase, and where the connection sits
Who exhibits at Kochi venues, and what that changes
The sector mix in Kochi is spices, tourism, seafood, coir and ayurveda, and each of those brings its own non-negotiables onto a stand. The table below is what we design against at purpose-built exhibition or trade centre before a single visual is drawn, because most of these requirements are structural or electrical rather than decorative.
Most Kochi exhibitors are selling to more than one of those audiences, which is an argument for a layout rather than a style. Give the coir audience the frontage and the ayurveda audience the back corner, and the stand stops trying to be two things in the same square metre.
Kochi's sector mix and what each needs from a stand
| Sector | What the stand has to do |
|---|---|
| Coir | Coir products are bulky and tactile. Open stacking, a handling table and generous top light do more than cabinetry, because the audience is buying texture. |
| Ayurveda | Ayurveda exhibitors sell provenance and trust, so the stand needs a clean dispensing counter, labelled product on open shelving, and a private corner for a consultation. |
| Spices | Spice stands work on aroma and colour. Open sample jars within reach, sealed bulk storage, good top light, and a counter where grades and quantities can be discussed. |
| Tourism | Tourism stands sell a place. Large imagery high up, a literature counter, seating for an itinerary conversation, and screen content that reads from the aisle without sound. |
| Seafood | Seafood exhibitors often need chilled display, which means a drained wet area, a dedicated power point for refrigeration, ventilation and a wipe-clean counter. |
The sectors listed are the ones that drive exhibiting activity across Kerala. Where your show draws from more than one of them, the space plan below is where the compromise gets resolved.
Services
What we build at Adlux International Convention & Exhibition Centre
Exhibition Stall Design
Concept-to-3D stall design that stops visitors in the aisle.
Stall Fabrication
In-house carpentry, metal and print for flawless builds.
Custom Exhibition Booths
One-of-a-kind booths built around your brand.
Modular Exhibition Stalls
Reusable, quick-install stalls for frequent exhibitors.
Octanorm & System Stalls
Clean aluminium shell-scheme and system booths.
Double-Decker Stalls
Two-storey stands that double your space.
Pavilion Design
State, industry and association pavilions.
Country Pavilions
National pavilions at Indian and global expos.
Trade Show Booths
High-impact booths for B2B trade shows.
Exhibition Stand Builders
End-to-end stand building with on-site crews.
Event Stage Fabrication
Stages, backdrops and sets for events.
AV & LED Wall Support
LED walls, sound, screens and AV crews.
Stall sizes and lead times for Adlux International Convention & Exhibition Centre
Most stands at a venue like this fall between 9 and 72 sq.m. The table below uses the same formula as our stall planner — storage at 10% of area up to 18 sq.m and 15% above, a meeting corner at 5% unless you are hosting meetings, display taking the remainder — so you can sanity-check a quote against the space you have actually booked.
Read the display column rather than the size column. A 36 sq.m stand carries about 28.8 sq.m of usable display once storage and a meeting corner are taken out, which is the number that decides how much product and how many people the stand can actually hold.
Space, staffing and lead time by stall size
| Stall size | Footprint | Likely layout | Display | Staff | Visitors at once | Build weeks |
|---|---|---|---|---|---|---|
| 9 sq.m | 3 × 3 m | Inline or corner | 7.6 sq.m | 2 | 3 | 3 |
| 18 sq.m | 3 × 6 m | Inline or corner | 15.3 sq.m | 2 | 6 | 3 |
| 36 sq.m | 6 × 6 m | Corner or three-side open | 28.8 sq.m | 4 | 11 | 4 |
| 54 sq.m | 6 × 9 m | Corner or three-side open | 43.2 sq.m | 6 | 17 | 5 |
| 72 sq.m | 6 × 12 m | Three-side open or island | 57.6 sq.m | 8 | 23 | 5 |
Custom stalls typically run ₹9,000–₹18,000 per sq.m for the build; modular and octanorm construction costs less, and an upgraded shell scheme less again. AV, furniture, flooring, transport and taxes are quoted on separate lines.
Designing a stand that works at Adlux International Convention & Exhibition Centre
Hall shows are walked at pace along long aisles, so the stand has to answer what you do from twenty metres and why it matters from two. Two messages at two distances, not one message twice.
Plan the stand around one decision: what do you want a visitor to do in the ninety seconds they will give you? Everything else — the graphic hierarchy, where staff stand, where the product sits — follows from answering that honestly.
Because Kochi's show calendar leans towards spices, tourism and seafood, the stands we build at this venue usually need to balance open display against a private corner for commercial conversations.
How a build at Adlux International Convention & Exhibition Centre runs
01
Read the venue pack
Before anything is drawn we ask for the organiser's pack for your edition: the stand plan with open sides marked, the build-up and dismantle windows, and the rules on height, rigging, fixing and power. At purpose-built exhibition or trade centre the answer that most often changes a design is the build height allowance, the rigging deadline and the power load ordered at booking.
02
Design to the limits
Design happens against the constraints rather than around them, so a height and rigging strategy ordered to the organiser's deadline, and a metered power load is a starting condition here rather than a late revision. What you approve in 3D is therefore something that can actually be built in this room.
03
Build and test in the workshop
The stall is fabricated and then stood up in our own workshop: panels numbered, graphics trial-fitted, circuits tested and lamps aimed. Problems get found where there is time to fix them rather than at purpose-built exhibition or trade centre at midnight.
04
Install, hand over, strike
On site the work is assembly rather than fabrication, which is the whole point of the previous stage. At purpose-built exhibition or trade centre the install also covers aisle clearance by the organiser's published deadline, and the same crew comes back to strike the stand and clear the space.
What else is in Kochi
We cover 3 other named exhibition venues in Kochi: Lulu Bolgatty International Convention Centre, CIAL Trade Fair & Exhibition Centre and Rajiv Gandhi Indoor Stadium. By name they break down into 1 convention centre, 1 purpose-built exhibition or trade centre and 1 indoor stadium or arena, and the gap between the easiest and the hardest of those to build in is larger than any gap in stall size.
Underneath the named venues sit the 11 venue categories we cover in every city, Kochi included: university & college campuses, industry association halls, stadium & sports complexes, corporate campus event spaces, industrial estate expo grounds, government exhibition grounds, resort & lawn venues, 5-star hotel ballrooms, convention & banquet halls, open exhibition grounds and mall atriums. A large share of exhibiting activity in India happens in those rooms rather than in exhibition halls, which is why they get their own pages rather than a footnote.
Named Kochi venues, read by what each one calls itself
| Venue | Type read from the name | What that implies for a stand |
|---|---|---|
| Lulu Bolgatty International Convention Centre | Convention centre | Banquet halls put stands close together, so the differentiator is usually light rather than size. |
| CIAL Trade Fair & Exhibition Centre | Purpose-built exhibition or trade centre | Hall shows are walked at pace along long aisles, so the stand has to answer what you do from twenty metres and why it matters from two. |
| Rajiv Gandhi Indoor Stadium | Indoor stadium or arena | In a volume this large a stand reads as small unless it builds upward or lights upward. |
A venue's name is a strong hint and not a specification. We confirm height, rigging, fixing, power and hours from the organiser's pack for your edition before design sign-off.
Every Kochi venue we cover
Build-up
Build-up, access and approvals in Kochi
Build-up in Kochi usually runs on the organiser's schedule rather than yours, and the practical constraint is access: one loading bay shared by every exhibitor, a lift queue, and a hard stop when the hall closes. We pre-assemble in the workshop and number every panel so our time on site is assembly, not fabrication.
Design, fabrication, graphics, lighting, flooring, furniture, installation and dismantle can all sit on one quote, which is usually cheaper than sourcing them separately once you account for three margins and the coordination time.
What we handle for you
- Organiser drawings, electrical load details and approvals in the format Kochi organisers ask for
- Design checked against height, rigging, fixing and fire rules before sign-off
- Pre-assembly and electrical testing in the workshop before dispatch
- Transport, installation and an on-site crew inside the build-up window
- Dismantle and clearing the stand inside the dismantle period
Exhibiting elsewhere in Kerala
Kochi is one of 4 Kerala cities on our list, alongside Thiruvananthapuram, Kozhikode and Thrissur. For an exhibitor doing a state circuit that matters practically: the structure travels, the graphics are reprinted, and nobody has to re-engineer a stand for each stop.
A stand engineered for this venue is rarely a one-show asset. Frame-and-skin construction lets the structure be stored and re-skinned for the next city, which is why the second show in a programme costs materially less than the first.
If this venue is one stop on a programme, say so at design stage. A stand drawn to be reused is drawn differently — demountable joints, numbered panels, graphics on replaceable skins and a storage footprint that fits a standard crate — and retrofitting that later costs more than building it in.
01
Brief
Share stall size, expo and goals. We call within 2 hours.
02
3D Design
Photoreal concepts in 48 hours, revised until perfect.
03
Fabrication
Built and pre-assembled in our own workshops.
04
Install & Show
On-site crew builds, hands over and dismantles.
FAQ
Adlux International Convention & Exhibition Centre FAQ
Can you build at Adlux International Convention & Exhibition Centre?+
Yes. Adlux International Convention & Exhibition Centre is one of the Kochi venues our crews work at regularly, covering design, fabrication, installation and dismantle inside the organiser's window.
What does a stall at Adlux International Convention & Exhibition Centre cost?+
Custom stalls typically range from ₹9,000 to ₹18,000 per sq.m depending on size, finishes and AV; modular and octanorm builds cost less. Share your stand size and show dates for an itemised quote.
What are the build-up timings at Adlux International Convention & Exhibition Centre?+
Build-up windows are set by the organiser for each show rather than by the venue alone, so we confirm them in writing for your edition and plan the build — including night shifts if needed — around them.
How early should I book for a show at Adlux International Convention & Exhibition Centre?+
Four to six weeks ahead for a custom stall and eight or more for a double-decker or pavilion. Urgent builds in seven to ten days are possible with a simplified design.
Who is on site during build-up at Adlux International Convention & Exhibition Centre?+
A named project manager and the crew that pre-assembled the stall. They install to the drawing, hand over a working stand and return to dismantle and clear it within the organiser's window.
Can you work to a shell scheme at Adlux International Convention & Exhibition Centre?+
Yes. Where the organiser supplies shell scheme panels we upgrade them with printed fabric or vinyl, raised flooring, spotlights and a branded counter, which lifts the stand a long way at modest cost.
Does a stand in an exhibition hall need platform flooring?+
Not structurally — the slab is built for load. Platform flooring in a hall is a design decision: it lifts the stand, hides cable runs and gives a finished edge, and it is worth the height allowance it uses when the stand has services to conceal.
How is power ordered for an exhibition hall stand?+
As a metered allocation through the organiser at booking, with single or three-phase options. The load is declared rather than estimated, because adding capacity during build-up is slow and costs considerably more than ordering it correctly.
Do you design differently for spices exhibitors here?+
Yes. Kochi's show calendar is driven by spices, tourism, seafood, coir and ayurveda, and the sector decides the fundamentals — how much product has to be on open display, how private the meeting space needs to be, whether the floor has to carry load and whether water, drainage or three-phase power are required. We brief against the sector before the identity.
Can the same stand be used at another Kerala venue?+
Usually, if it is built for it. We cover 4 Kerala cities including Kochi, Thiruvananthapuram, Kozhikode and Thrissur, and a frame-and-skin stand can be stored, re-skinned with new graphics and rebuilt at the equivalent venue elsewhere in the state. Say so at design stage, because a reusable stand is detailed differently.
What is the biggest risk at purpose-built exhibition or trade centre?+
Discovering a constraint after fabrication. Rigging and power are ordered through the organiser against a deadline, so a design that depends on a hanging banner ordered late becomes a freestanding design at short notice. That is why we ask for the access route, the fixing rules, the power allocation and the build-up window in writing before anything is cut, rather than treating any of them as a site problem.
More in Kochi
Other Kerala cities we cover
Exhibiting soon? Let's build your stall.