Kochi venue
Stall fabrication at Open Exhibition Grounds, Kochi
Open grounds where hangar-style German-tent exhibitions and trade fairs are set up.
15
Kochi venues covered
4
Named exhibition venues
11
Venue categories
Tier 2
Kerala market
Exhibiting at Open Exhibition Grounds, Kochi
Open grounds where hangar-style German-tent exhibitions and trade fairs are set up. Our crews work to the organiser's build-up window at this venue, pre-assembling in the workshop so site time goes on assembly rather than fabrication.
The reason venue matters more than it looks is that it sets the limits the design has to obey — ceiling height, rigging, what you may fix to, how much power you are allocated and when you are allowed to work. We confirm those for your specific show before anything is cut, because a panel that will not pass the access door is an expensive discovery to make on site.
Placed against the rest of the Kochi list, Open Exhibition Grounds, Kochi is the most open end of it — no walls, no ceiling, no fixed limits, and no shelter either. Knowing that before you design is what stops a stand being drawn for a hall and then built in a ballroom, which is the most expensive revision in this business.
Kochi is a growing exhibition market rather than a mature one, and the venues reflect that: 11 venue categories plus 4 named venues. Rooms are shared with other kinds of event, so the paperwork and the hours come from whoever owns the room rather than from an exhibition operator.
Building on an open exhibition ground
Open grounds give a builder the freedom indoor venues cannot: large panels delivered to the stand, height limited by the tent rather than a slab-to-soffit figure, and a vehicle alongside the build for as long as it is needed. The trade is that the specification has to survive rain, wind, heat and dust for the length of the show.
Open exhibition grounds vary from one address to the next even inside Kochi, so the figures below are the pattern rather than the contract. The organiser's pack for your show is what we actually design to.
What changes at open exhibition grounds
| Build input | At open exhibition grounds |
|---|---|
| Access route & panel sizes | Vehicles usually reach the stand itself, so panel size is limited by the truck and the crew rather than by a door. That is the one real structural advantage an open ground gives a builder. |
| Fixing method | Pegs, ballast and ground anchors, plus fixings into the hangar or tent frame where the organiser permits them. Tall elements are triangulated because there is nothing solid to lean against. |
| Power source | Generator supply with its own distribution and a backup path. Cable runs are long, so voltage drop, protected routing and crossing points across walkways are designed rather than discovered. |
| Floor protection | Raised platform flooring to level uneven ground, keep dust down and give cables a route. Underneath the platform, drainage matters as much as levelling does. |
| Build & strike hours | A longer build-up window than an indoor hall, because tenting, flooring and power all precede the stand. Daylight working is the norm and dust is continuous. |
| Weather & environment | The governing constraint. Rain, wind, heat and dust are all designed for — sealed edges, covered junctions, wind loading on anything tall, and no graphic that cannot take a shower. |
Read this as the pattern for open exhibition grounds, then check it against the organiser's pack. Where the two disagree, the pack wins and the drawing changes before the material does.
How we build for this kind of venue
- Raised platform flooring to level the ground, seal out dust and carry cable runs
- Weather protection and water ingress planned for, not improvised on the day
- Drainage considered under the platform as carefully as the levels above it
- Generator power with its own distribution and a backup path
- A longer build-up window because tenting, flooring and power precede the stand
- Edge sealing and covered electrical junctions as standard on an exposed site
What to ask the organiser about open exhibition grounds
Most of what goes wrong at open exhibition grounds goes wrong because a question was not asked early. These are the ones worth asking before you brief a designer, let alone a fabricator.
Get these in writing before you brief anyone
- Whether power is generator or mains, the allocation per stand, and the distance to the connection point
- The build-up sequence, since flooring and tenting have to be finished before stands begin
- Overnight security arrangements on an open site
- Wind-loading limits on tall or hanging elements, and whether any are barred outright
- Vehicle access to the stand itself, and for how long a vehicle may remain
- The ground surface — levelled earth, hardstanding or turf — and whether pegging is permitted
Who exhibits at Kochi venues, and what that changes
Exhibitors at Kochi venues come mainly from spices, tourism, seafood, coir and ayurveda — the sectors that fill Kerala's show floors. Those audiences do not want the same stand, and at open exhibition grounds the difference shows up in the build rather than in the brief: who needs a closed room, who needs a load-rated floor, who needs water and drainage, who needs nothing but a screen and two chairs.
Most Kochi exhibitors are selling to more than one of those audiences, which is an argument for a layout rather than a style. Give the coir audience the frontage and the ayurveda audience the back corner, and the stand stops trying to be two things in the same square metre.
Kochi's sector mix and what each needs from a stand
| Sector | What the stand has to do |
|---|---|
| Coir | Coir products are bulky and tactile. Open stacking, a handling table and generous top light do more than cabinetry, because the audience is buying texture. |
| Ayurveda | Ayurveda exhibitors sell provenance and trust, so the stand needs a clean dispensing counter, labelled product on open shelving, and a private corner for a consultation. |
| Spices | Spice stands work on aroma and colour. Open sample jars within reach, sealed bulk storage, good top light, and a counter where grades and quantities can be discussed. |
| Tourism | Tourism stands sell a place. Large imagery high up, a literature counter, seating for an itinerary conversation, and screen content that reads from the aisle without sound. |
| Seafood | Seafood exhibitors often need chilled display, which means a drained wet area, a dedicated power point for refrigeration, ventilation and a wipe-clean counter. |
The sectors listed are the ones that drive exhibiting activity across Kerala. Where your show draws from more than one of them, the space plan below is where the compromise gets resolved.
Services
What we build at Open Exhibition Grounds, Kochi
Exhibition Stall Design
Concept-to-3D stall design that stops visitors in the aisle.
Stall Fabrication
In-house carpentry, metal and print for flawless builds.
Custom Exhibition Booths
One-of-a-kind booths built around your brand.
Modular Exhibition Stalls
Reusable, quick-install stalls for frequent exhibitors.
Octanorm & System Stalls
Clean aluminium shell-scheme and system booths.
Double-Decker Stalls
Two-storey stands that double your space.
Pavilion Design
State, industry and association pavilions.
Country Pavilions
National pavilions at Indian and global expos.
Trade Show Booths
High-impact booths for B2B trade shows.
Exhibition Stand Builders
End-to-end stand building with on-site crews.
Event Stage Fabrication
Stages, backdrops and sets for events.
AV & LED Wall Support
LED walls, sound, screens and AV crews.
Stall sizes and lead times for Open Exhibition Grounds, Kochi
Most stands at a venue like this fall between 9 and 72 sq.m. The table below uses the same formula as our stall planner — storage at 10% of area up to 18 sq.m and 15% above, a meeting corner at 5% unless you are hosting meetings, display taking the remainder — so you can sanity-check a quote against the space you have actually booked.
Read the display column rather than the size column. A 36 sq.m stand carries about 28.8 sq.m of usable display once storage and a meeting corner are taken out, which is the number that decides how much product and how many people the stand can actually hold.
Space, staffing and lead time by stall size
| Stall size | Footprint | Likely layout | Display | Staff | Visitors at once | Build weeks |
|---|---|---|---|---|---|---|
| 9 sq.m | 3 × 3 m | Inline or corner | 7.6 sq.m | 2 | 3 | 3 |
| 18 sq.m | 3 × 6 m | Inline or corner | 15.3 sq.m | 2 | 6 | 3 |
| 36 sq.m | 6 × 6 m | Corner or three-side open | 28.8 sq.m | 4 | 11 | 4 |
| 54 sq.m | 6 × 9 m | Corner or three-side open | 43.2 sq.m | 6 | 17 | 5 |
| 72 sq.m | 6 × 12 m | Three-side open or island | 57.6 sq.m | 8 | 23 | 5 |
Custom stalls typically run ₹9,000–₹18,000 per sq.m for the build; modular and octanorm construction costs less, and an upgraded shell scheme less again. AV, furniture, flooring, transport and taxes are quoted on separate lines.
Designing a stand that works at Open Exhibition Grounds, Kochi
Open-ground visitors arrive hot, dusty and already tired of walking. A shaded standing area with somewhere to put a bag converts better than another graphic wall, and it costs less.
Plan the stand around one decision: what do you want a visitor to do in the ninety seconds they will give you? Everything else — the graphic hierarchy, where staff stand, where the product sits — follows from answering that honestly.
Exhibitors here come largely from spices, tourism and seafood, and a spices audience has specific expectations: product visible, specification available, and somewhere to talk without shouting. We design for that rather than applying a generic layout.
How a build at open exhibition grounds runs
01
Read the venue pack
The job starts with paperwork rather than with a concept. We want the stand plan, the access route, the power allocation and the permitted working hours in writing, and at open exhibition grounds we pay particular attention to whether tenting and flooring are provided by the organiser, and when they will be finished.
02
Design to the limits
Design happens against the constraints rather than around them, so platform flooring, sealed edges, wind loading on tall elements and generator distribution is a starting condition here rather than a late revision. What you approve in 3D is therefore something that can actually be built in this room.
03
Build and test in the workshop
Carpentry, metalwork, spray finishing, large-format print and electrical assembly all happen in-house, and the whole stall is assembled once before it ships. That is what turns a short on-site window into enough time.
04
Install, hand over, strike
A named project manager and the crew that pre-assembled the stall install it to the drawing and hand over a working stand. Site care is part of that rather than an afterthought: levelling, dust sealing at the platform edges and covered electrical junctions. The same crew returns to dismantle and clear the stand inside the organiser's window.
What else is in Kochi
Kochi gives you more than one kind of room. Alongside this page we cover 4 named exhibition venues in the city — Adlux International Convention & Exhibition Centre, Lulu Bolgatty International Convention Centre, CIAL Trade Fair & Exhibition Centre and Rajiv Gandhi Indoor Stadium. Read by what each one calls itself, that list comprises 2 purpose-built exhibition and trade centres, 1 convention centre and 1 indoor stadium or arena: 3 different build specifications inside one city.
Underneath the named venues sit the 11 venue categories we cover in every city, Kochi included: corporate campus event spaces, industrial estate expo grounds, government exhibition grounds, resort & lawn venues, 5-star hotel ballrooms, convention & banquet halls, open exhibition grounds, mall atriums, university & college campuses, industry association halls and stadium & sports complexes. A large share of exhibiting activity in India happens in those rooms rather than in exhibition halls, which is why they get their own pages rather than a footnote.
Named Kochi venues, read by what each one calls itself
| Venue | Type read from the name | What that implies for a stand |
|---|---|---|
| Adlux International Convention & Exhibition Centre | Purpose-built exhibition or trade centre | Hall shows are walked at pace along long aisles, so the stand has to answer what you do from twenty metres and why it matters from two. |
| Lulu Bolgatty International Convention Centre | Convention centre | Banquet halls put stands close together, so the differentiator is usually light rather than size. |
| CIAL Trade Fair & Exhibition Centre | Purpose-built exhibition or trade centre | Hall shows are walked at pace along long aisles, so the stand has to answer what you do from twenty metres and why it matters from two. |
| Rajiv Gandhi Indoor Stadium | Indoor stadium or arena | In a volume this large a stand reads as small unless it builds upward or lights upward. |
A venue's name is a strong hint and not a specification. We confirm height, rigging, fixing, power and hours from the organiser's pack for your edition before design sign-off.
Every Kochi venue we cover
Build-up
Build-up, access and approvals in Kochi
Every Kochi venue issues its own build-up schedule, power allocation and list of what you may and may not fix to the structure. We read it before fabrication, because a panel that will not fit through the access door is an expensive thing to discover at the venue.
Everything the stand needs — structure, print, lighting, flooring, furniture, AV and the crew to install and strike it — can be bundled into a single itemised quote with one project manager behind it.
What we handle for you
- Organiser drawings, electrical load details and approvals in the format Kochi organisers ask for
- Design checked against height, rigging, fixing and fire rules before sign-off
- Pre-assembly and electrical testing in the workshop before dispatch
- Transport, installation and an on-site crew inside the build-up window
- Dismantle and clearing the stand inside the dismantle period
Exhibiting elsewhere in Kerala
Beyond Kochi we build in 3 other Kerala cities: Thiruvananthapuram, Kozhikode and Thrissur. Same drawings, same workshop, same project manager — which is what makes a second city cheaper than the first rather than a repeat of it.
Open exhibition grounds are not unique to Kochi either: we cover the same category in all 4 of the Kerala cities on our list, which means the access, fixing and power pattern described above travels with you. A stand built for open exhibition grounds here is usually re-skinnable for the equivalent venue in the next city rather than rebuildable.
A multi-city programme is mostly a logistics question rather than a design one. One approved drawing set, one set of reusable panels, graphics printed per city and a crew that travels with the stand — that is the whole model, and it is what keeps the per-city cost falling as the programme goes on.
01
Brief
Share stall size, expo and goals. We call within 2 hours.
02
3D Design
Photoreal concepts in 48 hours, revised until perfect.
03
Fabrication
Built and pre-assembled in our own workshops.
04
Install & Show
On-site crew builds, hands over and dismantles.
FAQ
Venue FAQ
Can you build at Open Exhibition Grounds, Kochi?+
Yes. We build at open exhibition grounds throughout Kochi, covering design, fabrication, installation and dismantle inside the organiser's window.
What does a stall at Open Exhibition Grounds, Kochi cost?+
Custom stalls typically range from ₹9,000 to ₹18,000 per sq.m depending on size, finishes and AV; modular and octanorm builds cost less. Share your stand size and show dates for an itemised quote.
What are the build-up timings at Open Exhibition Grounds, Kochi?+
Build-up windows are set by the organiser for each show rather than by the venue alone, so we confirm them in writing for your edition and plan the build — including night shifts if needed — around them.
How early should I book for a show at Open Exhibition Grounds, Kochi?+
Four to six weeks ahead for a custom stall and eight or more for a double-decker or pavilion. Urgent builds in seven to ten days are possible with a simplified design.
Can you provide AV, lighting and furniture at Open Exhibition Grounds, Kochi?+
Yes — LED walls, screens, lighting, furniture, flooring and carpeting can be bundled with the stall build on a single quote.
Do you handle approvals for Open Exhibition Grounds, Kochi?+
Yes. We prepare dimensioned drawings, electrical load details and structural documents to the organiser's format, and check the design against the venue's height, rigging and fire rules before fabrication.
How is power supplied on an open exhibition ground?+
Usually by generator, with distribution run out to the stands and a backup path for critical loads. We confirm the allocation and the distance to the connection point in advance, because long cable runs change both the cable specification and the cost.
What happens to an open-ground stand if it rains?+
A stand designed for the site takes it. Platform flooring lifts the build clear of standing water, edges are sealed, electrical junctions are covered, and graphics are specified in materials that tolerate a wetting rather than paper-faced boards that do not.
Do you design differently for spices exhibitors here?+
Yes. Kochi's show calendar is driven by spices, tourism, seafood, coir and ayurveda, and the sector decides the fundamentals — how much product has to be on open display, how private the meeting space needs to be, whether the floor has to carry load and whether water, drainage or three-phase power are required. We brief against the sector before the identity.
Can the same stand be used at another Kerala venue?+
Usually, if it is built for it. We cover 4 Kerala cities including Kochi, Thiruvananthapuram, Kozhikode and Thrissur, and a frame-and-skin stand can be stored, re-skinned with new graphics and rebuilt at the equivalent venue elsewhere in the state. Say so at design stage, because a reusable stand is detailed differently.
What is the biggest risk at open exhibition grounds?+
Discovering a constraint after fabrication. Flooring, tenting and generator power all precede your stand on an open ground, so a crew planned in for the first available day arrives before the site is ready for them. That is why we ask for the access route, the fixing rules, the power allocation and the build-up window in writing before anything is cut, rather than treating any of them as a site problem.
More in Kochi
Other Kerala cities we cover
Exhibiting soon? Let's build your stall.