Hyderabad venue
Stall fabrication at Government Exhibition Grounds, Hyderabad
Government-run haats and exhibition grounds used for handicraft, MSME and state fairs.
17
Hyderabad venues covered
6
Named exhibition venues
11
Venue categories
Tier 1
Telangana market
Exhibiting at Government Exhibition Grounds, Hyderabad
Government-run haats and exhibition grounds used for handicraft, MSME and state fairs. We design, fabricate, install and dismantle stalls here, with the organiser drawings and approvals prepared as part of the project rather than quoted as an extra.
A venue imposes a rulebook, and the stall has to be built to it: how high you can go, whether you can hang anything, what you may fix into the floor, how much power you get and which hours you can work. We read that rulebook at design stage, not at build-up.
Placed against the rest of the Hyderabad list, Government Exhibition Grounds, Hyderabad is the public end of it — the broadest audience, the longest run and the most documentary approvals. Knowing that before you design is what stops a stand being drawn for a hall and then built in a ballroom, which is the most expensive revision in this business.
As a Tier 1 exhibition city, Hyderabad carries 6 named venues as well as 11 venue categories, which is why two shows in the same week can need entirely different builds. The practical consequence of that density is congestion at build-up: shared bays, lift queues and a hard clearance deadline that nobody moves.
Building on a government exhibition ground
Government-run haats and exhibition grounds host handicraft, MSME and state fairs, and the approvals are documentary rather than commercial. Grounds are gated with a controlled vehicle list, passes are issued per crew member so the crew list is final earlier than usual, power is allocated by the department running the fair, and the build and strike hours are set and strictly kept at both ends.
Within Hyderabad the specific room still matters: two government exhibition grounds in the same city can differ on clear height, access and power. We confirm those in writing for your edition rather than carrying an assumption from the last build.
What changes at government exhibition grounds
| Build input | At government exhibition grounds |
|---|---|
| Access route & panel sizes | Gated grounds with a controlled vehicle list, then a carry to the stall. Passes are issued per crew member, so the crew list has to be final earlier than at a commercial show. |
| Fixing method | Pegs and ballast on open ground, freestanding on paved areas. Permanent structures, trees and paving are left untouched, which rules out leaning anything on them. |
| Power source | Ground distribution or generator, with an allocation set by the department running the fair. It is usually modest, so LED lighting and low-load fittings are the default rather than a choice. |
| Floor protection | Platform flooring over uneven ground with dust sealing at the edges, and protection boards over paved or heritage surfaces. |
| Build & strike hours | Set by the organising department and strict at both ends. Approvals are documentary, so the paperwork is prepared and lodged well before the build begins. |
| Weather & environment | Open or semi-covered, so rain and dust are planned for. These fairs often run a week or more, which makes durability a bigger issue than finish. |
Read this as the pattern for government exhibition grounds, then check it against the organiser's pack. Where the two disagree, the pack wins and the drawing changes before the material does.
How we build for this kind of venue
- A modest power allocation set by the organising department — LED lighting as default
- Signage sized to read across a wide public thoroughfare
- Protection boards over paved and heritage surfaces
- Gated grounds with a controlled vehicle list and passes issued per crew member
- Durable surfaces specified for a run of a week or more
- Documentary approvals prepared and submitted well ahead of the build
What to ask the organiser about government exhibition grounds
A quote for government exhibition grounds is an estimate until these answers exist, and a price afterwards. Ask the organiser for them in writing — not because anyone is being difficult, but because the same venue issues different rules for different shows.
Get these in writing before you brief anyone
- Which department issues approvals, in what format, and by what date
- The vehicle list and crew pass process, and the deadline for submitting names
- The power allocation per stall and whether supply is mains or generator
- Overnight security on the ground and whether stock may be left on the stand
- The run length of the fair, since it decides the durability specification
- Restrictions near permanent structures, trees and paved or heritage surfaces
Who exhibits at Hyderabad venues, and what that changes
Exhibitors at Hyderabad venues come mainly from IT & software, pharma, biotech, defence and real estate — the sectors that fill Telangana's show floors. Those audiences do not want the same stand, and at government exhibition grounds the difference shows up in the build rather than in the brief: who needs a closed room, who needs a load-rated floor, who needs water and drainage, who needs nothing but a screen and two chairs.
Mixed-sector shows are the harder case. Real estate and IT & software visitors want opposite things from the same footprint, and the resolution is zoning rather than compromise: open display on the aisle face, a closed or semi-closed corner behind it, and storage that keeps the difference invisible.
Hyderabad's sector mix and what each needs from a stand
| Sector | What the stand has to do |
|---|---|
| Real estate | Real estate sells on models and screens. A scale model on a lit plinth, large visuals at eye height, and several seated pockets where a booking conversation can run twenty minutes. |
| IT & software | Software has nothing physical to show, so the stand sells with screens and conversation. Plan demo pods at standing height, a quiet zone or headphones, and a closed corner for a serious discussion. |
| Pharma | A pharma audience talks in private. A closed meeting corner, lockable sample storage, a wipe-clean dispensing counter and literature capacity matter more than open display area. |
| Biotech | Biotech conversations are technical and confidential. A bench-style demo area, a screen carrying data rather than imagery, and a closed meeting room are the working requirements. |
| Defence | Defence shows are access-controlled and document-heavy. Expect a closed briefing area, controlled sightlines into it, and display cases rather than open product. |
The sectors listed are the ones that drive exhibiting activity across Telangana. Where your show draws from more than one of them, the space plan below is where the compromise gets resolved.
Services
What we build at Government Exhibition Grounds, Hyderabad
Exhibition Stall Design
Concept-to-3D stall design that stops visitors in the aisle.
Stall Fabrication
In-house carpentry, metal and print for flawless builds.
Custom Exhibition Booths
One-of-a-kind booths built around your brand.
Modular Exhibition Stalls
Reusable, quick-install stalls for frequent exhibitors.
Octanorm & System Stalls
Clean aluminium shell-scheme and system booths.
Double-Decker Stalls
Two-storey stands that double your space.
Pavilion Design
State, industry and association pavilions.
Country Pavilions
National pavilions at Indian and global expos.
Trade Show Booths
High-impact booths for B2B trade shows.
Exhibition Stand Builders
End-to-end stand building with on-site crews.
Event Stage Fabrication
Stages, backdrops and sets for events.
AV & LED Wall Support
LED walls, sound, screens and AV crews.
Stall sizes and lead times for Government Exhibition Grounds, Hyderabad
Most stands at a venue like this fall between 9 and 72 sq.m. The table below uses the same formula as our stall planner — storage at 10% of area up to 18 sq.m and 15% above, a meeting corner at 5% unless you are hosting meetings, display taking the remainder — so you can sanity-check a quote against the space you have actually booked.
Read the display column rather than the size column. A 36 sq.m stand carries about 28.8 sq.m of usable display once storage and a meeting corner are taken out, which is the number that decides how much product and how many people the stand can actually hold.
Space, staffing and lead time by stall size
| Stall size | Footprint | Likely layout | Display | Staff | Visitors at once | Build weeks |
|---|---|---|---|---|---|---|
| 9 sq.m | 3 × 3 m | Inline or corner | 7.6 sq.m | 2 | 3 | 3 |
| 18 sq.m | 3 × 6 m | Inline or corner | 15.3 sq.m | 2 | 6 | 3 |
| 36 sq.m | 6 × 6 m | Corner or three-side open | 28.8 sq.m | 4 | 11 | 4 |
| 54 sq.m | 6 × 9 m | Corner or three-side open | 43.2 sq.m | 6 | 17 | 5 |
| 72 sq.m | 6 × 12 m | Three-side open or island | 57.6 sq.m | 8 | 23 | 5 |
Custom stalls typically run ₹9,000–₹18,000 per sq.m for the build; modular and octanorm construction costs less, and an upgraded shell scheme less again. AV, furniture, flooring, transport and taxes are quoted on separate lines.
Designing a stand that works at Government Exhibition Grounds, Hyderabad
A public fair that runs for a week draws a general audience, so durability and clarity beat finesse. Specify surfaces that survive constant handling and signage that works from across a wide thoroughfare.
Plan the stand around one decision: what do you want a visitor to do in the ninety seconds they will give you? Everything else — the graphic hierarchy, where staff stand, where the product sits — follows from answering that honestly.
The buyers at this venue tend to come from IT & software, pharma and biotech. That shapes the brief more than the aesthetics do — an IT & software visitor is looking for evidence, not atmosphere.
How a build at government exhibition grounds runs
01
Read the venue pack
Before anything is drawn we ask for the organiser's pack for your edition: the stand plan with open sides marked, the build-up and dismantle windows, and the rules on height, rigging, fixing and power. At government exhibition grounds the answer that most often changes a design is the department's approval format and the deadline for crew and vehicle lists.
02
Design to the limits
Design happens against the constraints rather than around them, so durable surfaces for a long run and an LED lighting load that fits a modest allocation is a starting condition here rather than a late revision. What you approve in 3D is therefore something that can actually be built in this room.
03
Build and test in the workshop
The stall is fabricated and then stood up in our own workshop: panels numbered, graphics trial-fitted, circuits tested and lamps aimed. Problems get found where there is time to fix them rather than at government exhibition grounds at midnight.
04
Install, hand over, strike
A named project manager and the crew that pre-assembled the stall install it to the drawing and hand over a working stand. Site care is part of that rather than an afterthought: platform flooring over uneven ground and protection boards on paved surfaces. The same crew returns to dismantle and clear the stand inside the organiser's window.
What else is in Hyderabad
Hyderabad gives you more than one kind of room. Alongside this page we cover 6 named exhibition venues in the city — HITEX Exhibition Centre, Hyderabad International Convention Centre (HICC), Nampally Exhibition Grounds, Shilpakala Vedika, Jalavihar and Novotel & HICC Halls. Read by what each one calls itself, that list comprises 2 event venues, 1 purpose-built exhibition or trade centre, 1 convention centre, 1 open ground or maidan and 1 hotel ballroom or hotel convention hall: 5 different build specifications inside one city.
We also cover 11 venue categories in Hyderabad — convention & banquet halls, open exhibition grounds, mall atriums, university & college campuses, industry association halls, stadium & sports complexes, corporate campus event spaces, industrial estate expo grounds, government exhibition grounds, resort & lawn venues and 5-star hotel ballrooms — because most Indian shows outside the top handful of cities happen in a room that was built for something else. Each of those categories has its own access, fixing and power pattern, and each gets its own page.
Named Hyderabad venues, read by what each one calls itself
| Venue | Type read from the name | What that implies for a stand |
|---|---|---|
| HITEX Exhibition Centre | Purpose-built exhibition or trade centre | Hall shows are walked at pace along long aisles, so the stand has to answer what you do from twenty metres and why it matters from two. |
| Hyderabad International Convention Centre (HICC) | Convention centre | A pillar-less hall gives you a long sightline down the aisle, which makes the face that reads from thirty metres away worth more than the one a visitor sees standing in front of you. |
| Nampally Exhibition Grounds | Open ground or maidan | On an open ground your competition is the sky, not the neighbouring stand. |
| Shilpakala Vedika | Event venue | Settle the one visitor action the stand exists to produce, then judge every design decision against it. |
| Jalavihar | Event venue | Settle the one visitor action the stand exists to produce, then judge every design decision against it. |
| Novotel & HICC Halls | Hotel ballroom or hotel convention hall | Ballroom audiences are corporate and arrive in groups, so seated conversation space earns its square metres here in a way it would not at a consumer show. |
A venue's name is a strong hint and not a specification. We confirm height, rigging, fixing, power and hours from the organiser's pack for your edition before design sign-off.
Every Hyderabad venue we cover
Build-up
Build-up, access and approvals in Hyderabad
In Hyderabad the schedule is the organiser's, not yours — which means the build has to be designed around a fixed window, a shared bay and a queue. Pre-assembly in the workshop is what turns that window from a risk into a routine.
You can take the whole scope or just part of it. Most exhibitors take design and build together and add AV and furniture to the same quote, because the alternative is reconciling three delivery schedules yourself.
What we handle for you
- Organiser drawings, electrical load details and approvals in the format Hyderabad organisers ask for
- Design checked against height, rigging, fixing and fire rules before sign-off
- Pre-assembly and electrical testing in the workshop before dispatch
- Transport, installation and an on-site crew inside the build-up window
- Dismantle and clearing the stand inside the dismantle period
Exhibiting elsewhere in Telangana
Telangana is not a one-city exhibition market. We cover 3 cities in the state — Hyderabad, Warangal and Karimnagar — with the same workshops, crews and project managers, so a programme that runs across several of them runs on one schedule rather than several.
Government exhibition grounds are not unique to Hyderabad either: we cover the same category in all 3 of the Telangana cities on our list, which means the access, fixing and power pattern described above travels with you. A stand built for government exhibition grounds here is usually re-skinnable for the equivalent venue in the next city rather than rebuildable.
If this venue is one stop on a programme, say so at design stage. A stand drawn to be reused is drawn differently — demountable joints, numbered panels, graphics on replaceable skins and a storage footprint that fits a standard crate — and retrofitting that later costs more than building it in.
01
Brief
Share stall size, expo and goals. We call within 2 hours.
02
3D Design
Photoreal concepts in 48 hours, revised until perfect.
03
Fabrication
Built and pre-assembled in our own workshops.
04
Install & Show
On-site crew builds, hands over and dismantles.
FAQ
Venue FAQ
Can you build at Government Exhibition Grounds, Hyderabad?+
Yes. We build at government exhibition grounds throughout Hyderabad, covering design, fabrication, installation and dismantle inside the organiser's window.
What does a stall at Government Exhibition Grounds, Hyderabad cost?+
Custom stalls typically range from ₹9,000 to ₹18,000 per sq.m depending on size, finishes and AV; modular and octanorm builds cost less. Share your stand size and show dates for an itemised quote.
What are the build-up timings at Government Exhibition Grounds, Hyderabad?+
Build-up windows are set by the organiser for each show rather than by the venue alone, so we confirm them in writing for your edition and plan the build — including night shifts if needed — around them.
Do you handle approvals for Government Exhibition Grounds, Hyderabad?+
Yes. We prepare dimensioned drawings, electrical load details and structural documents to the organiser's format, and check the design against the venue's height, rigging and fire rules before fabrication.
Can you work to a shell scheme at Government Exhibition Grounds, Hyderabad?+
Yes. Where the organiser supplies shell scheme panels we upgrade them with printed fabric or vinyl, raised flooring, spotlights and a branded counter, which lifts the stand a long way at modest cost.
Can you provide AV, lighting and furniture at Government Exhibition Grounds, Hyderabad?+
Yes — LED walls, screens, lighting, furniture, flooring and carpeting can be bundled with the stall build on a single quote.
Is power limited at a state fair ground?+
Usually, yes. The allocation per stall is set by the organising department and tends to be modest, so lighting goes to LED, loads are declared honestly and anything heavy is agreed in advance rather than plugged in on the day.
How does a long fair run change the build?+
It moves the specification from finish to durability. A fair running a week or more means surfaces that take constant handling, graphics that do not scuff at hand height, stock storage sized for the whole run, and a stall that still looks maintained on the last day.
Do you design differently for IT & software exhibitors here?+
Yes. Hyderabad's show calendar is driven by IT & software, pharma, biotech, defence and real estate, and the sector decides the fundamentals — how much product has to be on open display, how private the meeting space needs to be, whether the floor has to carry load and whether water, drainage or three-phase power are required. We brief against the sector before the identity.
Can the same stand be used at another Telangana venue?+
Usually, if it is built for it. We cover 3 Telangana cities including Hyderabad, Warangal and Karimnagar, and a frame-and-skin stand can be stored, re-skinned with new graphics and rebuilt at the equivalent venue elsewhere in the state. Say so at design stage, because a reusable stand is detailed differently.
What is the biggest risk at government exhibition grounds?+
Discovering a constraint after fabrication. Approvals here are documentary and carry deadlines, and a stall whose paperwork is late does not get a pass onto the ground. That is why we ask for the access route, the fixing rules, the power allocation and the build-up window in writing before anything is cut, rather than treating any of them as a site problem.
More in Hyderabad
Other Telangana cities we cover
Exhibiting soon? Let's build your stall.