Hyderabad venue
Stall fabrication at Nampally Exhibition Grounds
Nampally Exhibition Grounds is one of Hyderabad's key exhibition venues, hosting trade fairs, consumer expos and corporate events throughout the year.
17
Hyderabad venues covered
6
Named exhibition venues
11
Venue categories
Tier 1
Telangana market
Exhibiting at Nampally Exhibition Grounds
Nampally Exhibition Grounds is one of Hyderabad's key exhibition venues, hosting trade fairs, consumer expos and corporate events throughout the year. We design, fabricate, install and dismantle stalls here, with the organiser drawings and approvals prepared as part of the project rather than quoted as an extra.
The reason venue matters more than it looks is that it sets the limits the design has to obey — ceiling height, rigging, what you may fix to, how much power you are allocated and when you are allowed to work. We confirm those for your specific show before anything is cut, because a panel that will not pass the access door is an expensive discovery to make on site.
Of the 17 Hyderabad venues we cover, this one occupies the most open end of it — no walls, no ceiling, no fixed limits, and no shelter either. Exhibitors tend to compare venues on footfall and cost; builders compare them on access, fixing and power, and on that measure the gap between the extremes of the Hyderabad list is very wide.
As a Tier 1 exhibition city, Hyderabad carries 6 named venues as well as 11 venue categories, which is why two shows in the same week can need entirely different builds. The practical consequence of that density is congestion at build-up: shared bays, lift queues and a hard clearance deadline that nobody moves.
Building on an open exhibition ground
An open ground is the most flexible and the most exposed option in any city. There is no door to limit panel size and usually no ceiling to limit height, because vehicles can reach the stand itself — but weather, dust, ground level and generator power all have to be designed in rather than assumed, and a hangar or German tent normally sits over the top of the whole thing.
Nampally Exhibition Grounds is read here as an open ground or maidan, which is how we plan a build until the organiser's pack for your edition says otherwise. The pack is what settles height, rigging, fixing, power and hours for a specific show, and the same building can issue different rules for two shows in the same month.
What changes at Nampally Exhibition Grounds
| Build input | At a venue of this kind |
|---|---|
| Access route & panel sizes | Vehicles usually reach the stand itself, so panel size is limited by the truck and the crew rather than by a door. That is the one real structural advantage an open ground gives a builder. |
| Fixing method | Pegs, ballast and ground anchors, plus fixings into the hangar or tent frame where the organiser permits them. Tall elements are triangulated because there is nothing solid to lean against. |
| Power source | Generator supply with its own distribution and a backup path. Cable runs are long, so voltage drop, protected routing and crossing points across walkways are designed rather than discovered. |
| Floor protection | Raised platform flooring to level uneven ground, keep dust down and give cables a route. Underneath the platform, drainage matters as much as levelling does. |
| Build & strike hours | A longer build-up window than an indoor hall, because tenting, flooring and power all precede the stand. Daylight working is the norm and dust is continuous. |
| Weather & environment | The governing constraint. Rain, wind, heat and dust are all designed for — sealed edges, covered junctions, wind loading on anything tall, and no graphic that cannot take a shower. |
Every row here is a design input rather than a detail. Two stands of identical area in Hyderabad can need completely different engineering because these six answers differ, which is why we settle them before anything is cut.
How we build for this kind of venue
- Weather protection and water ingress planned for, not improvised on the day
- Drainage considered under the platform as carefully as the levels above it
- Generator power with its own distribution and a backup path
- Panels sized by the truck and the crew rather than by a door
- Wind loading accounted for on every tall, hanging or fabric element
- A longer build-up window because tenting, flooring and power precede the stand
What to ask the organiser about Nampally Exhibition Grounds
Send the organiser this list before you commission anything. Each answer removes a contingency from the quote, and at open ground or maidan two or three of them change the structure rather than the finish.
Get these in writing before you brief anyone
- Whether power is generator or mains, the allocation per stand, and the distance to the connection point
- Vehicle access to the stand itself, and for how long a vehicle may remain
- The ground surface — levelled earth, hardstanding or turf — and whether pegging is permitted
- Wind-loading limits on tall or hanging elements, and whether any are barred outright
- Who is responsible for drainage and for standing water during the show
- Overnight security arrangements on an open site
Who exhibits at Hyderabad venues, and what that changes
The sector mix in Hyderabad is IT & software, pharma, biotech, defence and real estate, and each of those brings its own non-negotiables onto a stand. The table below is what we design against at open ground or maidan before a single visual is drawn, because most of these requirements are structural or electrical rather than decorative.
Most Hyderabad exhibitors are selling to more than one of those audiences, which is an argument for a layout rather than a style. Give the IT & software audience the frontage and the pharma audience the back corner, and the stand stops trying to be two things in the same square metre.
Hyderabad's sector mix and what each needs from a stand
| Sector | What the stand has to do |
|---|---|
| IT & software | Software has nothing physical to show, so the stand sells with screens and conversation. Plan demo pods at standing height, a quiet zone or headphones, and a closed corner for a serious discussion. |
| Pharma | A pharma audience talks in private. A closed meeting corner, lockable sample storage, a wipe-clean dispensing counter and literature capacity matter more than open display area. |
| Biotech | Biotech conversations are technical and confidential. A bench-style demo area, a screen carrying data rather than imagery, and a closed meeting room are the working requirements. |
| Defence | Defence shows are access-controlled and document-heavy. Expect a closed briefing area, controlled sightlines into it, and display cases rather than open product. |
| Real estate | Real estate sells on models and screens. A scale model on a lit plinth, large visuals at eye height, and several seated pockets where a booking conversation can run twenty minutes. |
The sectors listed are the ones that drive exhibiting activity across Telangana. Where your show draws from more than one of them, the space plan below is where the compromise gets resolved.
Services
What we build at Nampally Exhibition Grounds
Exhibition Stall Design
Concept-to-3D stall design that stops visitors in the aisle.
Stall Fabrication
In-house carpentry, metal and print for flawless builds.
Custom Exhibition Booths
One-of-a-kind booths built around your brand.
Modular Exhibition Stalls
Reusable, quick-install stalls for frequent exhibitors.
Octanorm & System Stalls
Clean aluminium shell-scheme and system booths.
Double-Decker Stalls
Two-storey stands that double your space.
Pavilion Design
State, industry and association pavilions.
Country Pavilions
National pavilions at Indian and global expos.
Trade Show Booths
High-impact booths for B2B trade shows.
Exhibition Stand Builders
End-to-end stand building with on-site crews.
Event Stage Fabrication
Stages, backdrops and sets for events.
AV & LED Wall Support
LED walls, sound, screens and AV crews.
Stall sizes and lead times for Nampally Exhibition Grounds
Most stands at a venue like this fall between 9 and 72 sq.m. The table below uses the same formula as our stall planner — storage at 10% of area up to 18 sq.m and 15% above, a meeting corner at 5% unless you are hosting meetings, display taking the remainder — so you can sanity-check a quote against the space you have actually booked.
Lead time is the column exhibitors underestimate. Three weeks is the base for a custom build, four from 24 sq.m and five from 54 sq.m, and those are fabrication weeks after design sign-off rather than from the day you first call. At open ground or maidan the build-up window itself is rarely the problem; the approval and fabrication time ahead of it usually is.
Space, staffing and lead time by stall size
| Stall size | Footprint | Likely layout | Display | Staff | Visitors at once | Build weeks |
|---|---|---|---|---|---|---|
| 9 sq.m | 3 × 3 m | Inline or corner | 7.6 sq.m | 2 | 3 | 3 |
| 18 sq.m | 3 × 6 m | Inline or corner | 15.3 sq.m | 2 | 6 | 3 |
| 36 sq.m | 6 × 6 m | Corner or three-side open | 28.8 sq.m | 4 | 11 | 4 |
| 54 sq.m | 6 × 9 m | Corner or three-side open | 43.2 sq.m | 6 | 17 | 5 |
| 72 sq.m | 6 × 12 m | Three-side open or island | 57.6 sq.m | 8 | 23 | 5 |
Custom stalls typically run ₹9,000–₹18,000 per sq.m for the build; modular and octanorm construction costs less, and an upgraded shell scheme less again. AV, furniture, flooring, transport and taxes are quoted on separate lines.
Designing a stand that works at Nampally Exhibition Grounds
Open-ground visitors arrive hot, dusty and already tired of walking. A shaded standing area with somewhere to put a bag converts better than another graphic wall, and it costs less.
Plan the stand around one decision: what do you want a visitor to do in the ninety seconds they will give you? Everything else — the graphic hierarchy, where staff stand, where the product sits — follows from answering that honestly.
Because Hyderabad's show calendar leans towards IT & software, pharma and biotech, the stands we build at this venue usually need to balance open display against a private corner for commercial conversations.
How a build at Nampally Exhibition Grounds runs
01
Read the venue pack
Before anything is drawn we ask for the organiser's pack for your edition: the stand plan with open sides marked, the build-up and dismantle windows, and the rules on height, rigging, fixing and power. At open ground or maidan the answer that most often changes a design is whether tenting and flooring are provided by the organiser, and when they will be finished.
02
Design to the limits
Design happens against the constraints rather than around them, so platform flooring, sealed edges, wind loading on tall elements and generator distribution is a starting condition here rather than a late revision. What you approve in 3D is therefore something that can actually be built in this room.
03
Build and test in the workshop
Carpentry, metalwork, spray finishing, large-format print and electrical assembly all happen in-house, and the whole stall is assembled once before it ships. That is what turns a short on-site window into enough time.
04
Install, hand over, strike
On site the work is assembly rather than fabrication, which is the whole point of the previous stage. At open ground or maidan the install also covers levelling, dust sealing at the platform edges and covered electrical junctions, and the same crew comes back to strike the stand and clear the space.
What else is in Hyderabad
The named venue list for Hyderabad runs to 5 buildings on top of this one: HITEX Exhibition Centre, Hyderabad International Convention Centre (HICC), Shilpakala Vedika, Jalavihar and Novotel & HICC Halls. Taking each name at its word, they divide into 2 event venues, 1 purpose-built exhibition or trade centre, 1 convention centre and 1 hotel ballroom or hotel convention hall — which is why a stand that worked at one Hyderabad venue is not automatically a stand that works at the next.
We also cover 11 venue categories in Hyderabad — university & college campuses, industry association halls, stadium & sports complexes, corporate campus event spaces, industrial estate expo grounds, government exhibition grounds, resort & lawn venues, 5-star hotel ballrooms, convention & banquet halls, open exhibition grounds and mall atriums — because most Indian shows outside the top handful of cities happen in a room that was built for something else. Each of those categories has its own access, fixing and power pattern, and each gets its own page.
Named Hyderabad venues, read by what each one calls itself
| Venue | Type read from the name | What that implies for a stand |
|---|---|---|
| HITEX Exhibition Centre | Purpose-built exhibition or trade centre | Hall shows are walked at pace along long aisles, so the stand has to answer what you do from twenty metres and why it matters from two. |
| Hyderabad International Convention Centre (HICC) | Convention centre | A pillar-less hall gives you a long sightline down the aisle, which makes the face that reads from thirty metres away worth more than the one a visitor sees standing in front of you. |
| Shilpakala Vedika | Event venue | Settle the one visitor action the stand exists to produce, then judge every design decision against it. |
| Jalavihar | Event venue | Settle the one visitor action the stand exists to produce, then judge every design decision against it. |
| Novotel & HICC Halls | Hotel ballroom or hotel convention hall | Ballroom audiences are corporate and arrive in groups, so seated conversation space earns its square metres here in a way it would not at a consumer show. |
A venue's name is a strong hint and not a specification. We confirm height, rigging, fixing, power and hours from the organiser's pack for your edition before design sign-off.
Every Hyderabad venue we cover
Build-up
Build-up, access and approvals in Hyderabad
In Hyderabad the schedule is the organiser's, not yours — which means the build has to be designed around a fixed window, a shared bay and a queue. Pre-assembly in the workshop is what turns that window from a risk into a routine.
Design, fabrication, graphics, lighting, flooring, furniture, installation and dismantle can all sit on one quote, which is usually cheaper than sourcing them separately once you account for three margins and the coordination time.
What we handle for you
- Organiser drawings, electrical load details and approvals in the format Hyderabad organisers ask for
- Design checked against height, rigging, fixing and fire rules before sign-off
- Pre-assembly and electrical testing in the workshop before dispatch
- Transport, installation and an on-site crew inside the build-up window
- Dismantle and clearing the stand inside the dismantle period
Exhibiting elsewhere in Telangana
Hyderabad is one of 3 Telangana cities on our list, alongside Warangal and Karimnagar. For an exhibitor doing a state circuit that matters practically: the structure travels, the graphics are reprinted, and nobody has to re-engineer a stand for each stop.
A stand engineered for this venue is rarely a one-show asset. Frame-and-skin construction lets the structure be stored and re-skinned for the next city, which is why the second show in a programme costs materially less than the first.
If this venue is one stop on a programme, say so at design stage. A stand drawn to be reused is drawn differently — demountable joints, numbered panels, graphics on replaceable skins and a storage footprint that fits a standard crate — and retrofitting that later costs more than building it in.
01
Brief
Share stall size, expo and goals. We call within 2 hours.
02
3D Design
Photoreal concepts in 48 hours, revised until perfect.
03
Fabrication
Built and pre-assembled in our own workshops.
04
Install & Show
On-site crew builds, hands over and dismantles.
FAQ
Nampally Exhibition Grounds FAQ
Can you build at Nampally Exhibition Grounds?+
Yes. Nampally Exhibition Grounds is one of the Hyderabad venues our crews work at regularly, covering design, fabrication, installation and dismantle inside the organiser's window.
What does a stall at Nampally Exhibition Grounds cost?+
Custom stalls typically range from ₹9,000 to ₹18,000 per sq.m depending on size, finishes and AV; modular and octanorm builds cost less. Share your stand size and show dates for an itemised quote.
What are the build-up timings at Nampally Exhibition Grounds?+
Build-up windows are set by the organiser for each show rather than by the venue alone, so we confirm them in writing for your edition and plan the build — including night shifts if needed — around them.
Can you provide AV, lighting and furniture at Nampally Exhibition Grounds?+
Yes — LED walls, screens, lighting, furniture, flooring and carpeting can be bundled with the stall build on a single quote.
Who is on site during build-up at Nampally Exhibition Grounds?+
A named project manager and the crew that pre-assembled the stall. They install to the drawing, hand over a working stand and return to dismantle and clear it within the organiser's window.
Do you handle approvals for Nampally Exhibition Grounds?+
Yes. We prepare dimensioned drawings, electrical load details and structural documents to the organiser's format, and check the design against the venue's height, rigging and fire rules before fabrication.
Is build-up longer on an open ground?+
Yes. Tenting, flooring and power distribution all have to be finished before stand building starts, so the organiser's build-up period is longer than an indoor hall's and the sequence is published. We plan our arrival against that sequence rather than against the first available day.
How is power supplied on an open exhibition ground?+
Usually by generator, with distribution run out to the stands and a backup path for critical loads. We confirm the allocation and the distance to the connection point in advance, because long cable runs change both the cable specification and the cost.
Do you design differently for IT & software exhibitors here?+
Yes. Hyderabad's show calendar is driven by IT & software, pharma, biotech, defence and real estate, and the sector decides the fundamentals — how much product has to be on open display, how private the meeting space needs to be, whether the floor has to carry load and whether water, drainage or three-phase power are required. We brief against the sector before the identity.
Can the same stand be used at another Telangana venue?+
Usually, if it is built for it. We cover 3 Telangana cities including Hyderabad, Warangal and Karimnagar, and a frame-and-skin stand can be stored, re-skinned with new graphics and rebuilt at the equivalent venue elsewhere in the state. Say so at design stage, because a reusable stand is detailed differently.
What is the biggest risk at open ground or maidan?+
Discovering a constraint after fabrication. Flooring, tenting and generator power all precede your stand on an open ground, so a crew planned in for the first available day arrives before the site is ready for them. That is why we ask for the access route, the fixing rules, the power allocation and the build-up window in writing before anything is cut, rather than treating any of them as a site problem.
More in Hyderabad
Other Telangana cities we cover
Exhibiting soon? Let's build your stall.