Bengaluru venue
Stall fabrication at Open Exhibition Grounds, Bengaluru
Open grounds where hangar-style German-tent exhibitions and trade fairs are set up.
18
Bengaluru venues covered
7
Named exhibition venues
11
Venue categories
Tier 1
Karnataka market
Exhibiting at Open Exhibition Grounds, Bengaluru
Open grounds where hangar-style German-tent exhibitions and trade fairs are set up. Everything from the first 3D concept to clearing the stand after dismantle is handled by one team and one project manager.
A venue imposes a rulebook, and the stall has to be built to it: how high you can go, whether you can hang anything, what you may fix into the floor, how much power you get and which hours you can work. We read that rulebook at design stage, not at build-up.
Placed against the rest of the Bengaluru list, Open Exhibition Grounds, Bengaluru is the most open end of it — no walls, no ceiling, no fixed limits, and no shelter either. Knowing that before you design is what stops a stand being drawn for a hall and then built in a ballroom, which is the most expensive revision in this business.
As a Tier 1 exhibition city, Bengaluru carries 7 named venues as well as 11 venue categories, which is why two shows in the same week can need entirely different builds. The practical consequence of that density is congestion at build-up: shared bays, lift queues and a hard clearance deadline that nobody moves.
Building on an open exhibition ground
Open grounds give a builder the freedom indoor venues cannot: large panels delivered to the stand, height limited by the tent rather than a slab-to-soffit figure, and a vehicle alongside the build for as long as it is needed. The trade is that the specification has to survive rain, wind, heat and dust for the length of the show.
Open exhibition grounds vary from one address to the next even inside Bengaluru, so the figures below are the pattern rather than the contract. The organiser's pack for your show is what we actually design to.
What changes at open exhibition grounds
| Build input | At open exhibition grounds |
|---|---|
| Access route & panel sizes | Vehicles usually reach the stand itself, so panel size is limited by the truck and the crew rather than by a door. That is the one real structural advantage an open ground gives a builder. |
| Fixing method | Pegs, ballast and ground anchors, plus fixings into the hangar or tent frame where the organiser permits them. Tall elements are triangulated because there is nothing solid to lean against. |
| Power source | Generator supply with its own distribution and a backup path. Cable runs are long, so voltage drop, protected routing and crossing points across walkways are designed rather than discovered. |
| Floor protection | Raised platform flooring to level uneven ground, keep dust down and give cables a route. Underneath the platform, drainage matters as much as levelling does. |
| Build & strike hours | A longer build-up window than an indoor hall, because tenting, flooring and power all precede the stand. Daylight working is the norm and dust is continuous. |
| Weather & environment | The governing constraint. Rain, wind, heat and dust are all designed for — sealed edges, covered junctions, wind loading on anything tall, and no graphic that cannot take a shower. |
Every row here is a design input rather than a detail. Two stands of identical area in Bengaluru can need completely different engineering because these six answers differ, which is why we settle them before anything is cut.
How we build for this kind of venue
- Drainage considered under the platform as carefully as the levels above it
- Panels sized by the truck and the crew rather than by a door
- Wind loading accounted for on every tall, hanging or fabric element
- A longer build-up window because tenting, flooring and power precede the stand
- Edge sealing and covered electrical junctions as standard on an exposed site
- Generator power with its own distribution and a backup path
What to ask the organiser about open exhibition grounds
A quote for open exhibition grounds is an estimate until these answers exist, and a price afterwards. Ask the organiser for them in writing — not because anyone is being difficult, but because the same venue issues different rules for different shows.
Get these in writing before you brief anyone
- The ground surface — levelled earth, hardstanding or turf — and whether pegging is permitted
- Who is responsible for drainage and for standing water during the show
- Overnight security arrangements on an open site
- Whether tenting or a hangar is provided by the organiser, and the clear height under it
- Wind-loading limits on tall or hanging elements, and whether any are barred outright
- Whether power is generator or mains, the allocation per stand, and the distance to the connection point
Who exhibits at Bengaluru venues, and what that changes
The sector mix in Bengaluru is IT & software, aerospace, biotech, electronics and coffee & food, and each of those brings its own non-negotiables onto a stand. The table below is what we design against at open exhibition grounds before a single visual is drawn, because most of these requirements are structural or electrical rather than decorative.
Mixed-sector shows are the harder case. Aerospace and biotech visitors want opposite things from the same footprint, and the resolution is zoning rather than compromise: open display on the aisle face, a closed or semi-closed corner behind it, and storage that keeps the difference invisible.
Bengaluru's sector mix and what each needs from a stand
| Sector | What the stand has to do |
|---|---|
| Aerospace | Aerospace buyers come for components and certification. Expect scale models and cutaways on plinths, a secure cabinet for restricted material, and a closed room for anything export-controlled. |
| Biotech | Biotech conversations are technical and confidential. A bench-style demo area, a screen carrying data rather than imagery, and a closed meeting room are the working requirements. |
| Electronics | Electronics audiences expect working units, which makes clean power with surge protection, cable management that survives three show days, and glare-free screen angles the first decisions. |
| Coffee & food | Coffee and food need a serviced counter — water, drainage, equipment power, a bin out of sight — and a queue that forms inside your stand rather than across the aisle. |
| IT & software | Software has nothing physical to show, so the stand sells with screens and conversation. Plan demo pods at standing height, a quiet zone or headphones, and a closed corner for a serious discussion. |
The sectors listed are the ones that drive exhibiting activity across Karnataka. Where your show draws from more than one of them, the space plan below is where the compromise gets resolved.
Services
What we build at Open Exhibition Grounds, Bengaluru
Exhibition Stall Design
Concept-to-3D stall design that stops visitors in the aisle.
Stall Fabrication
In-house carpentry, metal and print for flawless builds.
Custom Exhibition Booths
One-of-a-kind booths built around your brand.
Modular Exhibition Stalls
Reusable, quick-install stalls for frequent exhibitors.
Octanorm & System Stalls
Clean aluminium shell-scheme and system booths.
Double-Decker Stalls
Two-storey stands that double your space.
Pavilion Design
State, industry and association pavilions.
Country Pavilions
National pavilions at Indian and global expos.
Trade Show Booths
High-impact booths for B2B trade shows.
Exhibition Stand Builders
End-to-end stand building with on-site crews.
Event Stage Fabrication
Stages, backdrops and sets for events.
AV & LED Wall Support
LED walls, sound, screens and AV crews.
Stall sizes and lead times for Open Exhibition Grounds, Bengaluru
Most stands at a venue like this fall between 9 and 72 sq.m. The table below uses the same formula as our stall planner — storage at 10% of area up to 18 sq.m and 15% above, a meeting corner at 5% unless you are hosting meetings, display taking the remainder — so you can sanity-check a quote against the space you have actually booked.
Read the display column rather than the size column. A 36 sq.m stand carries about 28.8 sq.m of usable display once storage and a meeting corner are taken out, which is the number that decides how much product and how many people the stand can actually hold.
Space, staffing and lead time by stall size
| Stall size | Footprint | Likely layout | Display | Staff | Visitors at once | Build weeks |
|---|---|---|---|---|---|---|
| 9 sq.m | 3 × 3 m | Inline or corner | 7.6 sq.m | 2 | 3 | 3 |
| 18 sq.m | 3 × 6 m | Inline or corner | 15.3 sq.m | 2 | 6 | 3 |
| 36 sq.m | 6 × 6 m | Corner or three-side open | 28.8 sq.m | 4 | 11 | 4 |
| 54 sq.m | 6 × 9 m | Corner or three-side open | 43.2 sq.m | 6 | 17 | 5 |
| 72 sq.m | 6 × 12 m | Three-side open or island | 57.6 sq.m | 8 | 23 | 5 |
Custom stalls typically run ₹9,000–₹18,000 per sq.m for the build; modular and octanorm construction costs less, and an upgraded shell scheme less again. AV, furniture, flooring, transport and taxes are quoted on separate lines.
Designing a stand that works at Open Exhibition Grounds, Bengaluru
Open-ground visitors arrive hot, dusty and already tired of walking. A shaded standing area with somewhere to put a bag converts better than another graphic wall, and it costs less.
Plan the stand around one decision: what do you want a visitor to do in the ninety seconds they will give you? Everything else — the graphic hierarchy, where staff stand, where the product sits — follows from answering that honestly.
Exhibitors here come largely from IT & software, aerospace and biotech, and an IT & software audience has specific expectations: product visible, specification available, and somewhere to talk without shouting. We design for that rather than applying a generic layout.
How a build at open exhibition grounds runs
01
Read the venue pack
Before anything is drawn we ask for the organiser's pack for your edition: the stand plan with open sides marked, the build-up and dismantle windows, and the rules on height, rigging, fixing and power. At open exhibition grounds the answer that most often changes a design is whether tenting and flooring are provided by the organiser, and when they will be finished.
02
Design to the limits
The concept is then developed inside those limits rather than adjusted to them afterwards. At open exhibition grounds that means designing for platform flooring, sealed edges, wind loading on tall elements and generator distribution from the first sketch instead of retrofitting it to a finished drawing.
03
Build and test in the workshop
The stall is fabricated and then stood up in our own workshop: panels numbered, graphics trial-fitted, circuits tested and lamps aimed. Problems get found where there is time to fix them rather than at open exhibition grounds at midnight.
04
Install, hand over, strike
On site the work is assembly rather than fabrication, which is the whole point of the previous stage. At open exhibition grounds the install also covers levelling, dust sealing at the platform edges and covered electrical junctions, and the same crew comes back to strike the stand and clear the space.
What else is in Bengaluru
Bengaluru gives you more than one kind of room. Alongside this page we cover 7 named exhibition venues in the city — Bangalore International Exhibition Centre (BIEC), KTPO Trade Centre, Whitefield, Palace Grounds, Bangalore International Centre, Tripura Vasini, Palace Grounds and Sheraton Grand & Hotel Convention Halls, plus 1 more. Read by what each one calls itself, that list comprises 3 purpose-built exhibition and trade centres, 3 open grounds and maidans and 1 hotel ballroom or hotel convention hall: 3 different build specifications inside one city.
Underneath the named venues sit the 11 venue categories we cover in every city, Bengaluru included: open exhibition grounds, mall atriums, university & college campuses, industry association halls, stadium & sports complexes, corporate campus event spaces, industrial estate expo grounds, government exhibition grounds, resort & lawn venues, 5-star hotel ballrooms and convention & banquet halls. A large share of exhibiting activity in India happens in those rooms rather than in exhibition halls, which is why they get their own pages rather than a footnote.
Named Bengaluru venues, read by what each one calls itself
| Venue | Type read from the name | What that implies for a stand |
|---|---|---|
| Bangalore International Exhibition Centre (BIEC) | Purpose-built exhibition or trade centre | Hall shows are walked at pace along long aisles, so the stand has to answer what you do from twenty metres and why it matters from two. |
| KTPO Trade Centre, Whitefield | Purpose-built exhibition or trade centre | In a purpose-built hall you are one of many stands with identical freedoms, so differentiation comes from the things the hall allows and most exhibitors never use: height, light and a clear reason to step in off the aisle.. |
| Palace Grounds | Open ground or maidan | On an open ground your competition is the sky, not the neighbouring stand. |
| Bangalore International Centre | Purpose-built exhibition or trade centre | Hall shows are walked at pace along long aisles, so the stand has to answer what you do from twenty metres and why it matters from two. |
| Tripura Vasini, Palace Grounds | Open ground or maidan | On an open ground your competition is the sky, not the neighbouring stand. |
| Sheraton Grand & Hotel Convention Halls | Hotel ballroom or hotel convention hall | Ballroom audiences are corporate and arrive in groups, so seated conversation space earns its square metres here in a way it would not at a consumer show. |
| Jayamahal Palace Grounds | Open ground or maidan | On an open ground your competition is the sky, not the neighbouring stand. |
A venue's name is a strong hint and not a specification. We confirm height, rigging, fixing, power and hours from the organiser's pack for your edition before design sign-off.
Every Bengaluru venue we cover
Build-up
Build-up, access and approvals in Bengaluru
In Bengaluru the schedule is the organiser's, not yours — which means the build has to be designed around a fixed window, a shared bay and a queue. Pre-assembly in the workshop is what turns that window from a risk into a routine.
Everything the stand needs — structure, print, lighting, flooring, furniture, AV and the crew to install and strike it — can be bundled into a single itemised quote with one project manager behind it.
What we handle for you
- Organiser drawings, electrical load details and approvals in the format Bengaluru organisers ask for
- Design checked against height, rigging, fixing and fire rules before sign-off
- Pre-assembly and electrical testing in the workshop before dispatch
- Transport, installation and an on-site crew inside the build-up window
- Dismantle and clearing the stand inside the dismantle period
Exhibiting elsewhere in Karnataka
Beyond Bengaluru we build in 5 other Karnataka cities: Mysuru, Mangaluru, Hubballi, Belagavi and Davanagere. Same drawings, same workshop, same project manager — which is what makes a second city cheaper than the first rather than a repeat of it.
Because we cover open exhibition grounds in all 6 Karnataka cities on our list, a stand designed for this venue type is designed for the state. The structure, the fixing method and the power assumptions carry over; only the footprint and the graphics change.
If this venue is one stop on a programme, say so at design stage. A stand drawn to be reused is drawn differently — demountable joints, numbered panels, graphics on replaceable skins and a storage footprint that fits a standard crate — and retrofitting that later costs more than building it in.
01
Brief
Share stall size, expo and goals. We call within 2 hours.
02
3D Design
Photoreal concepts in 48 hours, revised until perfect.
03
Fabrication
Built and pre-assembled in our own workshops.
04
Install & Show
On-site crew builds, hands over and dismantles.
FAQ
Venue FAQ
Can you build at Open Exhibition Grounds, Bengaluru?+
Yes. We build at open exhibition grounds throughout Bengaluru, covering design, fabrication, installation and dismantle inside the organiser's window.
What does a stall at Open Exhibition Grounds, Bengaluru cost?+
Custom stalls typically range from ₹9,000 to ₹18,000 per sq.m depending on size, finishes and AV; modular and octanorm builds cost less. Share your stand size and show dates for an itemised quote.
Who is on site during build-up at Open Exhibition Grounds, Bengaluru?+
A named project manager and the crew that pre-assembled the stall. They install to the drawing, hand over a working stand and return to dismantle and clear it within the organiser's window.
Can you provide AV, lighting and furniture at Open Exhibition Grounds, Bengaluru?+
Yes — LED walls, screens, lighting, furniture, flooring and carpeting can be bundled with the stall build on a single quote.
How early should I book for a show at Open Exhibition Grounds, Bengaluru?+
Four to six weeks ahead for a custom stall and eight or more for a double-decker or pavilion. Urgent builds in seven to ten days are possible with a simplified design.
Can you work to a shell scheme at Open Exhibition Grounds, Bengaluru?+
Yes. Where the organiser supplies shell scheme panels we upgrade them with printed fabric or vinyl, raised flooring, spotlights and a branded counter, which lifts the stand a long way at modest cost.
Is build-up longer on an open ground?+
Yes. Tenting, flooring and power distribution all have to be finished before stand building starts, so the organiser's build-up period is longer than an indoor hall's and the sequence is published. We plan our arrival against that sequence rather than against the first available day.
How is power supplied on an open exhibition ground?+
Usually by generator, with distribution run out to the stands and a backup path for critical loads. We confirm the allocation and the distance to the connection point in advance, because long cable runs change both the cable specification and the cost.
Do you design differently for IT & software exhibitors here?+
Yes. Bengaluru's show calendar is driven by IT & software, aerospace, biotech, electronics and coffee & food, and the sector decides the fundamentals — how much product has to be on open display, how private the meeting space needs to be, whether the floor has to carry load and whether water, drainage or three-phase power are required. We brief against the sector before the identity.
Can the same stand be used at another Karnataka venue?+
Usually, if it is built for it. We cover 6 Karnataka cities including Bengaluru, Mysuru, Mangaluru and Hubballi, and a frame-and-skin stand can be stored, re-skinned with new graphics and rebuilt at the equivalent venue elsewhere in the state. Say so at design stage, because a reusable stand is detailed differently.
What is the biggest risk at open exhibition grounds?+
Discovering a constraint after fabrication. Flooring, tenting and generator power all precede your stand on an open ground, so a crew planned in for the first available day arrives before the site is ready for them. That is why we ask for the access route, the fixing rules, the power allocation and the build-up window in writing before anything is cut, rather than treating any of them as a site problem.
More in Bengaluru
Other Karnataka cities we cover
Exhibiting soon? Let's build your stall.