Bengaluru venue
Stall fabrication at Palace Grounds
Palace Grounds is one of Bengaluru's key exhibition venues, hosting trade fairs, consumer expos and corporate events throughout the year.
18
Bengaluru venues covered
7
Named exhibition venues
11
Venue categories
Tier 1
Karnataka market
Exhibiting at Palace Grounds
Palace Grounds is one of Bengaluru's key exhibition venues, hosting trade fairs, consumer expos and corporate events throughout the year. Our crews work to the organiser's build-up window at this venue, pre-assembling in the workshop so site time goes on assembly rather than fabrication.
The reason venue matters more than it looks is that it sets the limits the design has to obey — ceiling height, rigging, what you may fix to, how much power you are allocated and when you are allowed to work. We confirm those for your specific show before anything is cut, because a panel that will not pass the access door is an expensive discovery to make on site.
Of the 18 Bengaluru venues we cover, this one occupies the most open end of it — no walls, no ceiling, no fixed limits, and no shelter either. Exhibitors tend to compare venues on footfall and cost; builders compare them on access, fixing and power, and on that measure the gap between the extremes of the Bengaluru list is very wide.
Bengaluru has the depth of a Tier 1 market — 7 named exhibition venues and 11 venue categories on our list. Depth helps with availability and hurts with scheduling, because every exhibitor in the hall is working to the same window through the same access point.
Building on an open exhibition ground
An open ground is the most flexible and the most exposed option in any city. There is no door to limit panel size and usually no ceiling to limit height, because vehicles can reach the stand itself — but weather, dust, ground level and generator power all have to be designed in rather than assumed, and a hangar or German tent normally sits over the top of the whole thing.
We treat Palace Grounds as an open ground or maidan for planning purposes and then confirm every figure against the organiser's exhibitor pack for your edition, because rules are issued per show rather than per building.
What changes at Palace Grounds
| Build input | At a venue of this kind |
|---|---|
| Access route & panel sizes | Vehicles usually reach the stand itself, so panel size is limited by the truck and the crew rather than by a door. That is the one real structural advantage an open ground gives a builder. |
| Fixing method | Pegs, ballast and ground anchors, plus fixings into the hangar or tent frame where the organiser permits them. Tall elements are triangulated because there is nothing solid to lean against. |
| Power source | Generator supply with its own distribution and a backup path. Cable runs are long, so voltage drop, protected routing and crossing points across walkways are designed rather than discovered. |
| Floor protection | Raised platform flooring to level uneven ground, keep dust down and give cables a route. Underneath the platform, drainage matters as much as levelling does. |
| Build & strike hours | A longer build-up window than an indoor hall, because tenting, flooring and power all precede the stand. Daylight working is the norm and dust is continuous. |
| Weather & environment | The governing constraint. Rain, wind, heat and dust are all designed for — sealed edges, covered junctions, wind loading on anything tall, and no graphic that cannot take a shower. |
Every row here is a design input rather than a detail. Two stands of identical area in Bengaluru can need completely different engineering because these six answers differ, which is why we settle them before anything is cut.
How we build for this kind of venue
- Drainage considered under the platform as carefully as the levels above it
- Panels sized by the truck and the crew rather than by a door
- Generator power with its own distribution and a backup path
- A longer build-up window because tenting, flooring and power precede the stand
- Edge sealing and covered electrical junctions as standard on an exposed site
- Wind loading accounted for on every tall, hanging or fabric element
What to ask the organiser about Palace Grounds
Send the organiser this list before you commission anything. Each answer removes a contingency from the quote, and at open ground or maidan two or three of them change the structure rather than the finish.
Get these in writing before you brief anyone
- Overnight security arrangements on an open site
- Who is responsible for drainage and for standing water during the show
- Whether power is generator or mains, the allocation per stand, and the distance to the connection point
- The build-up sequence, since flooring and tenting have to be finished before stands begin
- Wind-loading limits on tall or hanging elements, and whether any are barred outright
- Whether tenting or a hangar is provided by the organiser, and the clear height under it
Who exhibits at Bengaluru venues, and what that changes
IT & software, aerospace, biotech, electronics and coffee & food account for most of the exhibiting activity in Bengaluru, and the sector is a bigger design input than the brand is. A coffee & food visitor and an IT & software visitor will judge the same 18 sq.m by completely different criteria, so we brief against the sector first and the identity second.
Most Bengaluru exhibitors are selling to more than one of those audiences, which is an argument for a layout rather than a style. Give the coffee & food audience the frontage and the IT & software audience the back corner, and the stand stops trying to be two things in the same square metre.
Bengaluru's sector mix and what each needs from a stand
| Sector | What the stand has to do |
|---|---|
| Coffee & food | Coffee and food need a serviced counter — water, drainage, equipment power, a bin out of sight — and a queue that forms inside your stand rather than across the aisle. |
| IT & software | Software has nothing physical to show, so the stand sells with screens and conversation. Plan demo pods at standing height, a quiet zone or headphones, and a closed corner for a serious discussion. |
| Aerospace | Aerospace buyers come for components and certification. Expect scale models and cutaways on plinths, a secure cabinet for restricted material, and a closed room for anything export-controlled. |
| Biotech | Biotech conversations are technical and confidential. A bench-style demo area, a screen carrying data rather than imagery, and a closed meeting room are the working requirements. |
| Electronics | Electronics audiences expect working units, which makes clean power with surge protection, cable management that survives three show days, and glare-free screen angles the first decisions. |
The sectors listed are the ones that drive exhibiting activity across Karnataka. Where your show draws from more than one of them, the space plan below is where the compromise gets resolved.
Services
What we build at Palace Grounds
Exhibition Stall Design
Concept-to-3D stall design that stops visitors in the aisle.
Stall Fabrication
In-house carpentry, metal and print for flawless builds.
Custom Exhibition Booths
One-of-a-kind booths built around your brand.
Modular Exhibition Stalls
Reusable, quick-install stalls for frequent exhibitors.
Octanorm & System Stalls
Clean aluminium shell-scheme and system booths.
Double-Decker Stalls
Two-storey stands that double your space.
Pavilion Design
State, industry and association pavilions.
Country Pavilions
National pavilions at Indian and global expos.
Trade Show Booths
High-impact booths for B2B trade shows.
Exhibition Stand Builders
End-to-end stand building with on-site crews.
Event Stage Fabrication
Stages, backdrops and sets for events.
AV & LED Wall Support
LED walls, sound, screens and AV crews.
Stall sizes and lead times for Palace Grounds
Most stands at a venue like this fall between 9 and 72 sq.m. The table below uses the same formula as our stall planner — storage at 10% of area up to 18 sq.m and 15% above, a meeting corner at 5% unless you are hosting meetings, display taking the remainder — so you can sanity-check a quote against the space you have actually booked.
Read the display column rather than the size column. A 36 sq.m stand carries about 28.8 sq.m of usable display once storage and a meeting corner are taken out, which is the number that decides how much product and how many people the stand can actually hold.
Space, staffing and lead time by stall size
| Stall size | Footprint | Likely layout | Display | Staff | Visitors at once | Build weeks |
|---|---|---|---|---|---|---|
| 9 sq.m | 3 × 3 m | Inline or corner | 7.6 sq.m | 2 | 3 | 3 |
| 18 sq.m | 3 × 6 m | Inline or corner | 15.3 sq.m | 2 | 6 | 3 |
| 36 sq.m | 6 × 6 m | Corner or three-side open | 28.8 sq.m | 4 | 11 | 4 |
| 54 sq.m | 6 × 9 m | Corner or three-side open | 43.2 sq.m | 6 | 17 | 5 |
| 72 sq.m | 6 × 12 m | Three-side open or island | 57.6 sq.m | 8 | 23 | 5 |
Custom stalls typically run ₹9,000–₹18,000 per sq.m for the build; modular and octanorm construction costs less, and an upgraded shell scheme less again. AV, furniture, flooring, transport and taxes are quoted on separate lines.
Designing a stand that works at Palace Grounds
On an open ground your competition is the sky, not the neighbouring stand. Height, a roof line of your own and lighting that still works at dusk are what make a stand findable from the far side of the ground.
The most common mistake here is treating every wall as equally valuable. One face does most of the work; identify it from the stand plan, spend the budget on it, and treat the rest as support.
Because Bengaluru's show calendar leans towards IT & software, aerospace and biotech, the stands we build at this venue usually need to balance open display against a private corner for commercial conversations.
How a build at Palace Grounds runs
01
Read the venue pack
The job starts with paperwork rather than with a concept. We want the stand plan, the access route, the power allocation and the permitted working hours in writing, and at open ground or maidan we pay particular attention to whether tenting and flooring are provided by the organiser, and when they will be finished.
02
Design to the limits
Design happens against the constraints rather than around them, so platform flooring, sealed edges, wind loading on tall elements and generator distribution is a starting condition here rather than a late revision. What you approve in 3D is therefore something that can actually be built in this room.
03
Build and test in the workshop
The stall is fabricated and then stood up in our own workshop: panels numbered, graphics trial-fitted, circuits tested and lamps aimed. Problems get found where there is time to fix them rather than at open ground or maidan at midnight.
04
Install, hand over, strike
A named project manager and the crew that pre-assembled the stall install it to the drawing and hand over a working stand. Site care is part of that rather than an afterthought: levelling, dust sealing at the platform edges and covered electrical junctions. The same crew returns to dismantle and clear the stand inside the organiser's window.
What else is in Bengaluru
The named venue list for Bengaluru runs to 6 buildings on top of this one: Bangalore International Exhibition Centre (BIEC), KTPO Trade Centre, Whitefield, Bangalore International Centre, Tripura Vasini, Palace Grounds, Sheraton Grand & Hotel Convention Halls and Jayamahal Palace Grounds. Taking each name at its word, they divide into 3 purpose-built exhibition and trade centres, 2 open grounds and maidans and 1 hotel ballroom or hotel convention hall — which is why a stand that worked at one Bengaluru venue is not automatically a stand that works at the next.
Underneath the named venues sit the 11 venue categories we cover in every city, Bengaluru included: mall atriums, university & college campuses, industry association halls, stadium & sports complexes, corporate campus event spaces, industrial estate expo grounds, government exhibition grounds, resort & lawn venues, 5-star hotel ballrooms, convention & banquet halls and open exhibition grounds. A large share of exhibiting activity in India happens in those rooms rather than in exhibition halls, which is why they get their own pages rather than a footnote.
Named Bengaluru venues, read by what each one calls itself
| Venue | Type read from the name | What that implies for a stand |
|---|---|---|
| Bangalore International Exhibition Centre (BIEC) | Purpose-built exhibition or trade centre | Hall shows are walked at pace along long aisles, so the stand has to answer what you do from twenty metres and why it matters from two. |
| KTPO Trade Centre, Whitefield | Purpose-built exhibition or trade centre | In a purpose-built hall you are one of many stands with identical freedoms, so differentiation comes from the things the hall allows and most exhibitors never use: height, light and a clear reason to step in off the aisle.. |
| Bangalore International Centre | Purpose-built exhibition or trade centre | Hall shows are walked at pace along long aisles, so the stand has to answer what you do from twenty metres and why it matters from two. |
| Tripura Vasini, Palace Grounds | Open ground or maidan | On an open ground your competition is the sky, not the neighbouring stand. |
| Sheraton Grand & Hotel Convention Halls | Hotel ballroom or hotel convention hall | Ballroom audiences are corporate and arrive in groups, so seated conversation space earns its square metres here in a way it would not at a consumer show. |
| Jayamahal Palace Grounds | Open ground or maidan | On an open ground your competition is the sky, not the neighbouring stand. |
A venue's name is a strong hint and not a specification. We confirm height, rigging, fixing, power and hours from the organiser's pack for your edition before design sign-off.
Every Bengaluru venue we cover
Build-up
Build-up, access and approvals in Bengaluru
Every Bengaluru venue issues its own build-up schedule, power allocation and list of what you may and may not fix to the structure. We read it before fabrication, because a panel that will not fit through the access door is an expensive thing to discover at the venue.
Design, fabrication, graphics, lighting, flooring, furniture, installation and dismantle can all sit on one quote, which is usually cheaper than sourcing them separately once you account for three margins and the coordination time.
What we handle for you
- Organiser drawings, electrical load details and approvals in the format Bengaluru organisers ask for
- Design checked against height, rigging, fixing and fire rules before sign-off
- Pre-assembly and electrical testing in the workshop before dispatch
- Transport, installation and an on-site crew inside the build-up window
- Dismantle and clearing the stand inside the dismantle period
Exhibiting elsewhere in Karnataka
Beyond Bengaluru we build in 5 other Karnataka cities: Mysuru, Mangaluru, Hubballi, Belagavi and Davanagere. Same drawings, same workshop, same project manager — which is what makes a second city cheaper than the first rather than a repeat of it.
A stand engineered for this venue is rarely a one-show asset. Frame-and-skin construction lets the structure be stored and re-skinned for the next city, which is why the second show in a programme costs materially less than the first.
A multi-city programme is mostly a logistics question rather than a design one. One approved drawing set, one set of reusable panels, graphics printed per city and a crew that travels with the stand — that is the whole model, and it is what keeps the per-city cost falling as the programme goes on.
01
Brief
Share stall size, expo and goals. We call within 2 hours.
02
3D Design
Photoreal concepts in 48 hours, revised until perfect.
03
Fabrication
Built and pre-assembled in our own workshops.
04
Install & Show
On-site crew builds, hands over and dismantles.
FAQ
Palace Grounds FAQ
Can you build at Palace Grounds?+
Yes. Palace Grounds is one of the Bengaluru venues our crews work at regularly, covering design, fabrication, installation and dismantle inside the organiser's window.
What does a stall at Palace Grounds cost?+
Custom stalls typically range from ₹9,000 to ₹18,000 per sq.m depending on size, finishes and AV; modular and octanorm builds cost less. Share your stand size and show dates for an itemised quote.
Who is on site during build-up at Palace Grounds?+
A named project manager and the crew that pre-assembled the stall. They install to the drawing, hand over a working stand and return to dismantle and clear it within the organiser's window.
What are the build-up timings at Palace Grounds?+
Build-up windows are set by the organiser for each show rather than by the venue alone, so we confirm them in writing for your edition and plan the build — including night shifts if needed — around them.
Can you work to a shell scheme at Palace Grounds?+
Yes. Where the organiser supplies shell scheme panels we upgrade them with printed fabric or vinyl, raised flooring, spotlights and a branded counter, which lifts the stand a long way at modest cost.
Do you handle approvals for Palace Grounds?+
Yes. We prepare dimensioned drawings, electrical load details and structural documents to the organiser's format, and check the design against the venue's height, rigging and fire rules before fabrication.
What happens to an open-ground stand if it rains?+
A stand designed for the site takes it. Platform flooring lifts the build clear of standing water, edges are sealed, electrical junctions are covered, and graphics are specified in materials that tolerate a wetting rather than paper-faced boards that do not.
Is build-up longer on an open ground?+
Yes. Tenting, flooring and power distribution all have to be finished before stand building starts, so the organiser's build-up period is longer than an indoor hall's and the sequence is published. We plan our arrival against that sequence rather than against the first available day.
Do you design differently for IT & software exhibitors here?+
Yes. Bengaluru's show calendar is driven by IT & software, aerospace, biotech, electronics and coffee & food, and the sector decides the fundamentals — how much product has to be on open display, how private the meeting space needs to be, whether the floor has to carry load and whether water, drainage or three-phase power are required. We brief against the sector before the identity.
Can the same stand be used at another Karnataka venue?+
Usually, if it is built for it. We cover 6 Karnataka cities including Bengaluru, Mysuru, Mangaluru and Hubballi, and a frame-and-skin stand can be stored, re-skinned with new graphics and rebuilt at the equivalent venue elsewhere in the state. Say so at design stage, because a reusable stand is detailed differently.
What is the biggest risk at open ground or maidan?+
Discovering a constraint after fabrication. Flooring, tenting and generator power all precede your stand on an open ground, so a crew planned in for the first available day arrives before the site is ready for them. That is why we ask for the access route, the fixing rules, the power allocation and the build-up window in writing before anything is cut, rather than treating any of them as a site problem.
More in Bengaluru
Other Karnataka cities we cover
Exhibiting soon? Let's build your stall.