Delhi venue
Stall fabrication at Open Exhibition Grounds, Delhi
Open grounds where hangar-style German-tent exhibitions and trade fairs are set up.
19
Delhi venues covered
8
Named exhibition venues
11
Venue categories
Tier 1
Delhi market
Exhibiting at Open Exhibition Grounds, Delhi
Open grounds where hangar-style German-tent exhibitions and trade fairs are set up. We design, fabricate, install and dismantle stalls here, with the organiser drawings and approvals prepared as part of the project rather than quoted as an extra.
Two stands of identical size can need completely different engineering depending on the room they go into. Height limits, rigging availability, fixing restrictions, power allocation and build hours all change with the venue, and all of them are settled in writing before fabrication starts.
Of the 19 Delhi venues we cover, this one occupies the most open end of it — no walls, no ceiling, no fixed limits, and no shelter either. Exhibitors tend to compare venues on footfall and cost; builders compare them on access, fixing and power, and on that measure the gap between the extremes of the Delhi list is very wide.
As a Tier 1 exhibition city, Delhi carries 8 named venues as well as 11 venue categories, which is why two shows in the same week can need entirely different builds. The practical consequence of that density is congestion at build-up: shared bays, lift queues and a hard clearance deadline that nobody moves.
Building on an open exhibition ground
Open grounds give a builder the freedom indoor venues cannot: large panels delivered to the stand, height limited by the tent rather than a slab-to-soffit figure, and a vehicle alongside the build for as long as it is needed. The trade is that the specification has to survive rain, wind, heat and dust for the length of the show.
Open exhibition grounds vary from one address to the next even inside Delhi, so the figures below are the pattern rather than the contract. The organiser's pack for your show is what we actually design to.
What changes at open exhibition grounds
| Build input | At open exhibition grounds |
|---|---|
| Access route & panel sizes | Vehicles usually reach the stand itself, so panel size is limited by the truck and the crew rather than by a door. That is the one real structural advantage an open ground gives a builder. |
| Fixing method | Pegs, ballast and ground anchors, plus fixings into the hangar or tent frame where the organiser permits them. Tall elements are triangulated because there is nothing solid to lean against. |
| Power source | Generator supply with its own distribution and a backup path. Cable runs are long, so voltage drop, protected routing and crossing points across walkways are designed rather than discovered. |
| Floor protection | Raised platform flooring to level uneven ground, keep dust down and give cables a route. Underneath the platform, drainage matters as much as levelling does. |
| Build & strike hours | A longer build-up window than an indoor hall, because tenting, flooring and power all precede the stand. Daylight working is the norm and dust is continuous. |
| Weather & environment | The governing constraint. Rain, wind, heat and dust are all designed for — sealed edges, covered junctions, wind loading on anything tall, and no graphic that cannot take a shower. |
These six are the ones that change the stand rather than the drawing. Confirm them for your edition with the organiser and we will design to the answers; where an answer is unavailable we design to the conservative assumption and revise once it arrives.
How we build for this kind of venue
- Generator power with its own distribution and a backup path
- A longer build-up window because tenting, flooring and power precede the stand
- Weather protection and water ingress planned for, not improvised on the day
- Panels sized by the truck and the crew rather than by a door
- Wind loading accounted for on every tall, hanging or fabric element
- Edge sealing and covered electrical junctions as standard on an exposed site
What to ask the organiser about open exhibition grounds
Most of what goes wrong at open exhibition grounds goes wrong because a question was not asked early. These are the ones worth asking before you brief a designer, let alone a fabricator.
Get these in writing before you brief anyone
- Overnight security arrangements on an open site
- Vehicle access to the stand itself, and for how long a vehicle may remain
- The build-up sequence, since flooring and tenting have to be finished before stands begin
- Who is responsible for drainage and for standing water during the show
- Wind-loading limits on tall or hanging elements, and whether any are barred outright
- Whether power is generator or mains, the allocation per stand, and the distance to the connection point
Who exhibits at Delhi venues, and what that changes
Exhibitors at Delhi venues come mainly from IT & electronics, automobile, pharma, handicrafts and education — the sectors that fill Delhi's show floors. Those audiences do not want the same stand, and at open exhibition grounds the difference shows up in the build rather than in the brief: who needs a closed room, who needs a load-rated floor, who needs water and drainage, who needs nothing but a screen and two chairs.
Most Delhi exhibitors are selling to more than one of those audiences, which is an argument for a layout rather than a style. Give the pharma audience the frontage and the handicrafts audience the back corner, and the stand stops trying to be two things in the same square metre.
Delhi's sector mix and what each needs from a stand
| Sector | What the stand has to do |
|---|---|
| Pharma | A pharma audience talks in private. A closed meeting corner, lockable sample storage, a wipe-clean dispensing counter and literature capacity matter more than open display area. |
| Handicrafts | Handicraft stands sell density. Open shelving, sightlines into the stand rather than a counter across the front, and light aimed at the object instead of the ceiling. |
| Education | Education fairs run on queues and counselling. Standing-height counters, a seated corner for parents, brochure capacity, and a layout that absorbs a session-break rush without blocking the aisle. |
| IT & electronics | An IT and electronics audience expects working kit, which makes clean power, cable management and glare-free screen positions the first design decisions rather than the last. |
| Automobile | An automobile and components audience wants to touch the part. Plan a load-rated display platform, a cutaway or turntable at hip height, and circulation wide enough for a crowd around one vehicle. |
The sectors listed are the ones that drive exhibiting activity across Delhi. Where your show draws from more than one of them, the space plan below is where the compromise gets resolved.
Services
What we build at Open Exhibition Grounds, Delhi
Exhibition Stall Design
Concept-to-3D stall design that stops visitors in the aisle.
Stall Fabrication
In-house carpentry, metal and print for flawless builds.
Custom Exhibition Booths
One-of-a-kind booths built around your brand.
Modular Exhibition Stalls
Reusable, quick-install stalls for frequent exhibitors.
Octanorm & System Stalls
Clean aluminium shell-scheme and system booths.
Double-Decker Stalls
Two-storey stands that double your space.
Pavilion Design
State, industry and association pavilions.
Country Pavilions
National pavilions at Indian and global expos.
Trade Show Booths
High-impact booths for B2B trade shows.
Exhibition Stand Builders
End-to-end stand building with on-site crews.
Event Stage Fabrication
Stages, backdrops and sets for events.
AV & LED Wall Support
LED walls, sound, screens and AV crews.
Stall sizes and lead times for Open Exhibition Grounds, Delhi
Most stands at a venue like this fall between 9 and 72 sq.m. The table below uses the same formula as our stall planner — storage at 10% of area up to 18 sq.m and 15% above, a meeting corner at 5% unless you are hosting meetings, display taking the remainder — so you can sanity-check a quote against the space you have actually booked.
Read the display column rather than the size column. A 36 sq.m stand carries about 28.8 sq.m of usable display once storage and a meeting corner are taken out, which is the number that decides how much product and how many people the stand can actually hold.
Space, staffing and lead time by stall size
| Stall size | Footprint | Likely layout | Display | Staff | Visitors at once | Build weeks |
|---|---|---|---|---|---|---|
| 9 sq.m | 3 × 3 m | Inline or corner | 7.6 sq.m | 2 | 3 | 3 |
| 18 sq.m | 3 × 6 m | Inline or corner | 15.3 sq.m | 2 | 6 | 3 |
| 36 sq.m | 6 × 6 m | Corner or three-side open | 28.8 sq.m | 4 | 11 | 4 |
| 54 sq.m | 6 × 9 m | Corner or three-side open | 43.2 sq.m | 6 | 17 | 5 |
| 72 sq.m | 6 × 12 m | Three-side open or island | 57.6 sq.m | 8 | 23 | 5 |
Custom stalls typically run ₹9,000–₹18,000 per sq.m for the build; modular and octanorm construction costs less, and an upgraded shell scheme less again. AV, furniture, flooring, transport and taxes are quoted on separate lines.
Designing a stand that works at Open Exhibition Grounds, Delhi
Open-ground visitors arrive hot, dusty and already tired of walking. A shaded standing area with somewhere to put a bag converts better than another graphic wall, and it costs less.
Height and light are what buy visibility in a shared hall. Where the venue allows it, go up — a tall brand element or a hanging banner is read from across the floor in a way that floor-level graphics never are.
Exhibitors here come largely from IT & electronics, automobile and pharma, and an IT & electronics audience has specific expectations: product visible, specification available, and somewhere to talk without shouting. We design for that rather than applying a generic layout.
How a build at open exhibition grounds runs
01
Read the venue pack
Before anything is drawn we ask for the organiser's pack for your edition: the stand plan with open sides marked, the build-up and dismantle windows, and the rules on height, rigging, fixing and power. At open exhibition grounds the answer that most often changes a design is whether tenting and flooring are provided by the organiser, and when they will be finished.
02
Design to the limits
Design happens against the constraints rather than around them, so platform flooring, sealed edges, wind loading on tall elements and generator distribution is a starting condition here rather than a late revision. What you approve in 3D is therefore something that can actually be built in this room.
03
Build and test in the workshop
The stall is fabricated and then stood up in our own workshop: panels numbered, graphics trial-fitted, circuits tested and lamps aimed. Problems get found where there is time to fix them rather than at open exhibition grounds at midnight.
04
Install, hand over, strike
On site the work is assembly rather than fabrication, which is the whole point of the previous stage. At open exhibition grounds the install also covers levelling, dust sealing at the platform edges and covered electrical junctions, and the same crew comes back to strike the stand and clear the space.
What else is in Delhi
We cover 8 other named exhibition venues in Delhi: Bharat Mandapam (Pragati Maidan), Yashobhoomi – India International Convention & Expo Centre, NSIC Exhibition Complex, Okhla, Talkatora Indoor Stadium, Siri Fort Auditorium and JLN Stadium Complex, plus 2 more on the city page. By name they break down into 3 purpose-built exhibition and trade centres, 2 indoor stadiums and arenas, 1 auditorium, hall or cultural centre, 1 hotel ballroom or hotel convention hall and 1 open ground or maidan, and the gap between the easiest and the hardest of those to build in is larger than any gap in stall size.
Underneath the named venues sit the 11 venue categories we cover in every city, Delhi included: corporate campus event spaces, industrial estate expo grounds, government exhibition grounds, resort & lawn venues, 5-star hotel ballrooms, convention & banquet halls, open exhibition grounds, mall atriums, university & college campuses, industry association halls and stadium & sports complexes. A large share of exhibiting activity in India happens in those rooms rather than in exhibition halls, which is why they get their own pages rather than a footnote.
Named Delhi venues, read by what each one calls itself
| Venue | Type read from the name | What that implies for a stand |
|---|---|---|
| Bharat Mandapam (Pragati Maidan) | Purpose-built exhibition or trade centre | In a purpose-built hall you are one of many stands with identical freedoms, so differentiation comes from the things the hall allows and most exhibitors never use: height, light and a clear reason to step in off the aisle.. |
| Yashobhoomi – India International Convention & Expo Centre | Purpose-built exhibition or trade centre | Hall shows are walked at pace along long aisles, so the stand has to answer what you do from twenty metres and why it matters from two. |
| NSIC Exhibition Complex, Okhla | Purpose-built exhibition or trade centre | In a purpose-built hall you are one of many stands with identical freedoms, so differentiation comes from the things the hall allows and most exhibitors never use: height, light and a clear reason to step in off the aisle.. |
| Talkatora Indoor Stadium | Indoor stadium or arena | Stadium shows move a lot of visitors across a wide floor in both directions, so plan flow rather than frontage. |
| Siri Fort Auditorium | Auditorium, hall or cultural centre | Most of the real traffic at an auditorium venue is in the foyer and during the breaks, so put the stand where people queue and plan for everything to happen in twenty-minute bursts.. |
| JLN Stadium Complex | Indoor stadium or arena | Stadium shows move a lot of visitors across a wide floor in both directions, so plan flow rather than frontage. |
| Aerocity Hotel Convention Halls | Hotel ballroom or hotel convention hall | In a ballroom the room is already handsome, so a stand that competes with the chandeliers loses. |
| Dilli Haat INA | Open ground or maidan | Open-ground visitors arrive hot, dusty and already tired of walking. |
A venue's name is a strong hint and not a specification. We confirm height, rigging, fixing, power and hours from the organiser's pack for your edition before design sign-off.
Every Delhi venue we cover
Build-up
Build-up, access and approvals in Delhi
Logistics in Delhi come down to three things: how the panels reach the hall, how much power the stand is allocated, and when the organiser lets you work. All three are settled in writing before we cut material.
Design, fabrication, graphics, lighting, flooring, furniture, installation and dismantle can all sit on one quote, which is usually cheaper than sourcing them separately once you account for three margins and the coordination time.
What we handle for you
- Organiser drawings, electrical load details and approvals in the format Delhi organisers ask for
- Design checked against height, rigging, fixing and fire rules before sign-off
- Pre-assembly and electrical testing in the workshop before dispatch
- Transport, installation and an on-site crew inside the build-up window
- Dismantle and clearing the stand inside the dismantle period
Taking the same stand to another city
We cover Delhi as the Delhi entry on our list, so multi-city programmes from here normally run to Mumbai, Bengaluru, Chennai and Hyderabad or similar. One drawing set and one reusable structure is the pattern, with print as the only per-city cost of consequence.
A stand engineered for this venue is rarely a one-show asset. Frame-and-skin construction lets the structure be stored and re-skinned for the next city, which is why the second show in a programme costs materially less than the first.
A multi-city programme is mostly a logistics question rather than a design one. One approved drawing set, one set of reusable panels, graphics printed per city and a crew that travels with the stand — that is the whole model, and it is what keeps the per-city cost falling as the programme goes on.
01
Brief
Share stall size, expo and goals. We call within 2 hours.
02
3D Design
Photoreal concepts in 48 hours, revised until perfect.
03
Fabrication
Built and pre-assembled in our own workshops.
04
Install & Show
On-site crew builds, hands over and dismantles.
FAQ
Venue FAQ
Can you build at Open Exhibition Grounds, Delhi?+
Yes. We build at open exhibition grounds throughout Delhi, covering design, fabrication, installation and dismantle inside the organiser's window.
What does a stall at Open Exhibition Grounds, Delhi cost?+
Custom stalls typically range from ₹9,000 to ₹18,000 per sq.m depending on size, finishes and AV; modular and octanorm builds cost less. Share your stand size and show dates for an itemised quote.
How early should I book for a show at Open Exhibition Grounds, Delhi?+
Four to six weeks ahead for a custom stall and eight or more for a double-decker or pavilion. Urgent builds in seven to ten days are possible with a simplified design.
What are the build-up timings at Open Exhibition Grounds, Delhi?+
Build-up windows are set by the organiser for each show rather than by the venue alone, so we confirm them in writing for your edition and plan the build — including night shifts if needed — around them.
Who is on site during build-up at Open Exhibition Grounds, Delhi?+
A named project manager and the crew that pre-assembled the stall. They install to the drawing, hand over a working stand and return to dismantle and clear it within the organiser's window.
Can you provide AV, lighting and furniture at Open Exhibition Grounds, Delhi?+
Yes — LED walls, screens, lighting, furniture, flooring and carpeting can be bundled with the stall build on a single quote.
What happens to an open-ground stand if it rains?+
A stand designed for the site takes it. Platform flooring lifts the build clear of standing water, edges are sealed, electrical junctions are covered, and graphics are specified in materials that tolerate a wetting rather than paper-faced boards that do not.
How is power supplied on an open exhibition ground?+
Usually by generator, with distribution run out to the stands and a backup path for critical loads. We confirm the allocation and the distance to the connection point in advance, because long cable runs change both the cable specification and the cost.
Do you design differently for IT & electronics exhibitors here?+
Yes. Delhi's show calendar is driven by IT & electronics, automobile, pharma, handicrafts and education, and the sector decides the fundamentals — how much product has to be on open display, how private the meeting space needs to be, whether the floor has to carry load and whether water, drainage or three-phase power are required. We brief against the sector before the identity.
Can the same stand be used at a show in another city?+
Usually, if it is built for it. A frame-and-skin stand can be stored between shows, re-skinned with new graphics and rebuilt in another city, with print as the only significant per-city cost. It needs to be designed that way from the start rather than adapted later.
What is the biggest risk at open exhibition grounds?+
Discovering a constraint after fabrication. Flooring, tenting and generator power all precede your stand on an open ground, so a crew planned in for the first available day arrives before the site is ready for them. That is why we ask for the access route, the fixing rules, the power allocation and the build-up window in writing before anything is cut, rather than treating any of them as a site problem.
More in Delhi
Exhibiting soon? Let's build your stall.