Delhi venue
Stall fabrication at Resort & Lawn Venues, Delhi
Resort lawns and outdoor venues used for dealer meets and brand experiences.
19
Delhi venues covered
8
Named exhibition venues
11
Venue categories
Tier 1
Delhi market
Exhibiting at Resort & Lawn Venues, Delhi
Resort lawns and outdoor venues used for dealer meets and brand experiences. Our crews work to the organiser's build-up window at this venue, pre-assembling in the workshop so site time goes on assembly rather than fabrication.
The reason venue matters more than it looks is that it sets the limits the design has to obey — ceiling height, rigging, what you may fix to, how much power you are allocated and when you are allowed to work. We confirm those for your specific show before anything is cut, because a panel that will not pass the access door is an expensive discovery to make on site.
Of the 19 Delhi venues we cover, this one occupies the hospitality end of it — the most attractive setting and the most exposed build. Exhibitors tend to compare venues on footfall and cost; builders compare them on access, fixing and power, and on that measure the gap between the extremes of the Delhi list is very wide.
As a Tier 1 exhibition city, Delhi carries 8 named venues as well as 11 venue categories, which is why two shows in the same week can need entirely different builds. The practical consequence of that density is congestion at build-up: shared bays, lift queues and a hard clearance deadline that nobody moves.
Building at a resort or lawn venue
At a resort the venue is selling the view and so, usually, are you. The structures are therefore low and open, the flooring is a platform that levels and protects the turf, the power is hidden and silent, and the lighting is designed for after sunset because that is when the event actually happens.
Resort & lawn venues vary from one address to the next even inside Delhi, so the figures below are the pattern rather than the contract. The organiser's pack for your show is what we actually design to.
What changes at resort & lawn venues
| Build input | At resort & lawn venues |
|---|---|
| Access route & panel sizes | Guest driveways and garden paths rather than service routes. Deliveries are timed so that trucks never cross a guest area, and panels are sized to be carried the last stretch. |
| Fixing method | Pegged or ballasted on turf, freestanding on paved terraces. Irrigation lines and buried lighting are the reason pegging is agreed in writing and never assumed. |
| Power source | A generator in silent housing, screened and placed away from guest areas, with resort supply as the backup or the other way round. Cable runs are long and buried under matting. |
| Floor protection | Platform flooring to level turf and protect it, with drainage under the deck. Reinstating the lawn after strike belongs in the quote rather than in a later conversation. |
| Build & strike hours | Worked around guest occupancy and quiet hours, so the noisy work happens in a narrow daytime band and the finishing happens late in the evening. |
| Weather & environment | Fully exposed. Wind loading on fabric and tall elements, a wet-weather plan, and overnight dew on every surface all change the specification. |
Read this as the pattern for resort & lawn venues, then check it against the organiser's pack. Where the two disagree, the pack wins and the drawing changes before the material does.
How we build for this kind of venue
- Deliveries timed so trucks never cross a guest area
- Noisy work compressed into a daytime band inside the resort's quiet hours
- Wind loading assessed on fabric, tenting and every tall element
- Pegging agreed in writing because irrigation and buried lighting sit under the lawn
- Lawn and grounds reinstated after strike, costed in the quote rather than after it
- Weather cover and drainage planned in rather than added on
What to ask the organiser about resort & lawn venues
A quote for resort & lawn venues is an estimate until these answers exist, and a price afterwards. Ask the organiser for them in writing — not because anyone is being difficult, but because the same venue issues different rules for different shows.
Get these in writing before you brief anyone
- Quiet hours, and which hours permit power tools at all
- Whether power is resort supply or generator, and where a generator may be placed
- Guest occupancy during build-up, since it decides the whole schedule
- Clear height and footprint under any tenting the resort provides
- Delivery routes and timings that avoid guest areas, and any vehicle weight limit
- Weather contingency — what happens to the event, and to your stand, in rain
Who exhibits at Delhi venues, and what that changes
IT & electronics, automobile, pharma, handicrafts and education account for most of the exhibiting activity in Delhi, and the sector is a bigger design input than the brand is. A automobile visitor and a pharma visitor will judge the same 18 sq.m by completely different criteria, so we brief against the sector first and the identity second.
Most Delhi exhibitors are selling to more than one of those audiences, which is an argument for a layout rather than a style. Give the automobile audience the frontage and the pharma audience the back corner, and the stand stops trying to be two things in the same square metre.
Delhi's sector mix and what each needs from a stand
| Sector | What the stand has to do |
|---|---|
| Automobile | An automobile and components audience wants to touch the part. Plan a load-rated display platform, a cutaway or turntable at hip height, and circulation wide enough for a crowd around one vehicle. |
| Pharma | A pharma audience talks in private. A closed meeting corner, lockable sample storage, a wipe-clean dispensing counter and literature capacity matter more than open display area. |
| Handicrafts | Handicraft stands sell density. Open shelving, sightlines into the stand rather than a counter across the front, and light aimed at the object instead of the ceiling. |
| Education | Education fairs run on queues and counselling. Standing-height counters, a seated corner for parents, brochure capacity, and a layout that absorbs a session-break rush without blocking the aisle. |
| IT & electronics | An IT and electronics audience expects working kit, which makes clean power, cable management and glare-free screen positions the first design decisions rather than the last. |
The sectors listed are the ones that drive exhibiting activity across Delhi. Where your show draws from more than one of them, the space plan below is where the compromise gets resolved.
Services
What we build at Resort & Lawn Venues, Delhi
Exhibition Stall Design
Concept-to-3D stall design that stops visitors in the aisle.
Stall Fabrication
In-house carpentry, metal and print for flawless builds.
Custom Exhibition Booths
One-of-a-kind booths built around your brand.
Modular Exhibition Stalls
Reusable, quick-install stalls for frequent exhibitors.
Octanorm & System Stalls
Clean aluminium shell-scheme and system booths.
Double-Decker Stalls
Two-storey stands that double your space.
Pavilion Design
State, industry and association pavilions.
Country Pavilions
National pavilions at Indian and global expos.
Trade Show Booths
High-impact booths for B2B trade shows.
Exhibition Stand Builders
End-to-end stand building with on-site crews.
Event Stage Fabrication
Stages, backdrops and sets for events.
AV & LED Wall Support
LED walls, sound, screens and AV crews.
Stall sizes and lead times for Resort & Lawn Venues, Delhi
Most stands at a venue like this fall between 9 and 72 sq.m. The table below uses the same formula as our stall planner — storage at 10% of area up to 18 sq.m and 15% above, a meeting corner at 5% unless you are hosting meetings, display taking the remainder — so you can sanity-check a quote against the space you have actually booked.
The figures are the same ones our stall planner uses, so a quote can be checked against them line by line: storage at 10% of the area up to 18 sq.m and 15% above it, a meeting corner at 5% unless you are actually hosting meetings, display taking whatever remains, one staff member per 9 sq.m, and the number of visitors who can stand in the stall at once coming out at display area divided by 2.5.
Space, staffing and lead time by stall size
| Stall size | Footprint | Likely layout | Display | Staff | Visitors at once | Build weeks |
|---|---|---|---|---|---|---|
| 9 sq.m | 3 × 3 m | Inline or corner | 7.6 sq.m | 2 | 3 | 3 |
| 18 sq.m | 3 × 6 m | Inline or corner | 15.3 sq.m | 2 | 6 | 3 |
| 36 sq.m | 6 × 6 m | Corner or three-side open | 28.8 sq.m | 4 | 11 | 4 |
| 54 sq.m | 6 × 9 m | Corner or three-side open | 43.2 sq.m | 6 | 17 | 5 |
| 72 sq.m | 6 × 12 m | Three-side open or island | 57.6 sq.m | 8 | 23 | 5 |
Custom stalls typically run ₹9,000–₹18,000 per sq.m for the build; modular and octanorm construction costs less, and an upgraded shell scheme less again. AV, furniture, flooring, transport and taxes are quoted on separate lines.
Designing a stand that works at Resort & Lawn Venues, Delhi
Dealer meets at a lawn venue are social before they are commercial, so plan the stand around standing groups and a bar-height surface rather than around a counter and a queue.
Visitors decide whether to enter from several metres away, so the stand has to answer "what do you do?" before it answers anything else. One legible line at eye height does more than a wall of product shots.
The buyers at this venue tend to come from IT & electronics, automobile and pharma. That shapes the brief more than the aesthetics do — an IT & electronics visitor is looking for evidence, not atmosphere.
How a build at resort & lawn venues runs
01
Read the venue pack
Before anything is drawn we ask for the organiser's pack for your edition: the stand plan with open sides marked, the build-up and dismantle windows, and the rules on height, rigging, fixing and power. At resort & lawn venues the answer that most often changes a design is whether pegging is permitted, and where irrigation and buried lighting run.
02
Design to the limits
Design happens against the constraints rather than around them, so ballasted or agreed pegging, drainage under the deck and silent generator placement is a starting condition here rather than a late revision. What you approve in 3D is therefore something that can actually be built in this room.
03
Build and test in the workshop
The stall is fabricated and then stood up in our own workshop: panels numbered, graphics trial-fitted, circuits tested and lamps aimed. Problems get found where there is time to fix them rather than at resort & lawn venues at midnight.
04
Install, hand over, strike
A named project manager and the crew that pre-assembled the stall install it to the drawing and hand over a working stand. Site care is part of that rather than an afterthought: turf protection under the deck and the lawn reinstated after strike. The same crew returns to dismantle and clear the stand inside the organiser's window.
What else is in Delhi
The named venue list for Delhi runs to 8 buildings on top of this one: Bharat Mandapam (Pragati Maidan), Yashobhoomi – India International Convention & Expo Centre, NSIC Exhibition Complex, Okhla, Talkatora Indoor Stadium, Siri Fort Auditorium and JLN Stadium Complex, plus 2 others. Taking each name at its word, they divide into 3 purpose-built exhibition and trade centres, 2 indoor stadiums and arenas, 1 auditorium, hall or cultural centre, 1 hotel ballroom or hotel convention hall and 1 open ground or maidan — which is why a stand that worked at one Delhi venue is not automatically a stand that works at the next.
We also cover 11 venue categories in Delhi — university & college campuses, industry association halls, stadium & sports complexes, corporate campus event spaces, industrial estate expo grounds, government exhibition grounds, resort & lawn venues, 5-star hotel ballrooms, convention & banquet halls, open exhibition grounds and mall atriums — because most Indian shows outside the top handful of cities happen in a room that was built for something else. Each of those categories has its own access, fixing and power pattern, and each gets its own page.
Named Delhi venues, read by what each one calls itself
| Venue | Type read from the name | What that implies for a stand |
|---|---|---|
| Bharat Mandapam (Pragati Maidan) | Purpose-built exhibition or trade centre | In a purpose-built hall you are one of many stands with identical freedoms, so differentiation comes from the things the hall allows and most exhibitors never use: height, light and a clear reason to step in off the aisle.. |
| Yashobhoomi – India International Convention & Expo Centre | Purpose-built exhibition or trade centre | Hall shows are walked at pace along long aisles, so the stand has to answer what you do from twenty metres and why it matters from two. |
| NSIC Exhibition Complex, Okhla | Purpose-built exhibition or trade centre | In a purpose-built hall you are one of many stands with identical freedoms, so differentiation comes from the things the hall allows and most exhibitors never use: height, light and a clear reason to step in off the aisle.. |
| Talkatora Indoor Stadium | Indoor stadium or arena | Stadium shows move a lot of visitors across a wide floor in both directions, so plan flow rather than frontage. |
| Siri Fort Auditorium | Auditorium, hall or cultural centre | Most of the real traffic at an auditorium venue is in the foyer and during the breaks, so put the stand where people queue and plan for everything to happen in twenty-minute bursts.. |
| JLN Stadium Complex | Indoor stadium or arena | Stadium shows move a lot of visitors across a wide floor in both directions, so plan flow rather than frontage. |
| Aerocity Hotel Convention Halls | Hotel ballroom or hotel convention hall | In a ballroom the room is already handsome, so a stand that competes with the chandeliers loses. |
| Dilli Haat INA | Open ground or maidan | Open-ground visitors arrive hot, dusty and already tired of walking. |
A venue's name is a strong hint and not a specification. We confirm height, rigging, fixing, power and hours from the organiser's pack for your edition before design sign-off.
Every Delhi venue we cover
Build-up
Build-up, access and approvals in Delhi
Access, lift queues and a shared loading bay decide how long a build takes in Delhi far more than stall size does. Our crews work to the organiser's window, including night shifts where the schedule requires it, and clear the stand inside the dismantle period so no penalty lands on your deposit.
Everything the stand needs — structure, print, lighting, flooring, furniture, AV and the crew to install and strike it — can be bundled into a single itemised quote with one project manager behind it.
What we handle for you
- Organiser drawings, electrical load details and approvals in the format Delhi organisers ask for
- Design checked against height, rigging, fixing and fire rules before sign-off
- Pre-assembly and electrical testing in the workshop before dispatch
- Transport, installation and an on-site crew inside the build-up window
- Dismantle and clearing the stand inside the dismantle period
Taking the same stand to another city
Delhi is a single-city market on our list, so a programme here usually pairs Delhi with the nearest major exhibition cities — Mumbai, Bengaluru, Chennai and Hyderabad among them. The structure travels and the graphics are reprinted per city, which is cheaper than commissioning a second stand.
A stand engineered for this venue is rarely a one-show asset. Frame-and-skin construction lets the structure be stored and re-skinned for the next city, which is why the second show in a programme costs materially less than the first.
A multi-city programme is mostly a logistics question rather than a design one. One approved drawing set, one set of reusable panels, graphics printed per city and a crew that travels with the stand — that is the whole model, and it is what keeps the per-city cost falling as the programme goes on.
01
Brief
Share stall size, expo and goals. We call within 2 hours.
02
3D Design
Photoreal concepts in 48 hours, revised until perfect.
03
Fabrication
Built and pre-assembled in our own workshops.
04
Install & Show
On-site crew builds, hands over and dismantles.
FAQ
Venue FAQ
Can you build at Resort & Lawn Venues, Delhi?+
Yes. We build at resort & lawn venues throughout Delhi, covering design, fabrication, installation and dismantle inside the organiser's window.
What does a stall at Resort & Lawn Venues, Delhi cost?+
Custom stalls typically range from ₹9,000 to ₹18,000 per sq.m depending on size, finishes and AV; modular and octanorm builds cost less. Share your stand size and show dates for an itemised quote.
Who is on site during build-up at Resort & Lawn Venues, Delhi?+
A named project manager and the crew that pre-assembled the stall. They install to the drawing, hand over a working stand and return to dismantle and clear it within the organiser's window.
How early should I book for a show at Resort & Lawn Venues, Delhi?+
Four to six weeks ahead for a custom stall and eight or more for a double-decker or pavilion. Urgent builds in seven to ten days are possible with a simplified design.
What are the build-up timings at Resort & Lawn Venues, Delhi?+
Build-up windows are set by the organiser for each show rather than by the venue alone, so we confirm them in writing for your edition and plan the build — including night shifts if needed — around them.
Can you work to a shell scheme at Resort & Lawn Venues, Delhi?+
Yes. Where the organiser supplies shell scheme panels we upgrade them with printed fabric or vinyl, raised flooring, spotlights and a branded counter, which lifts the stand a long way at modest cost.
Can a stand be pegged into a resort lawn?+
Only with written agreement, because irrigation lines and buried garden lighting run under most resort lawns. Where pegging is not permitted we ballast instead, and in either case the turf is protected by platform flooring and reinstated after the strike.
How is power supplied at a lawn venue?+
Usually by generator in silent housing, placed and screened away from guest areas, with the resort's own supply as a backup. Cable runs are long, so they are routed under matting and sized for the distance rather than for the load alone.
Do you design differently for IT & electronics exhibitors here?+
Yes. Delhi's show calendar is driven by IT & electronics, automobile, pharma, handicrafts and education, and the sector decides the fundamentals — how much product has to be on open display, how private the meeting space needs to be, whether the floor has to carry load and whether water, drainage or three-phase power are required. We brief against the sector before the identity.
Can the same stand be used at a show in another city?+
Usually, if it is built for it. A frame-and-skin stand can be stored between shows, re-skinned with new graphics and rebuilt in another city, with print as the only significant per-city cost. It needs to be designed that way from the start rather than adapted later.
What is the biggest risk at resort & lawn venues?+
Discovering a constraint after fabrication. Whether a lawn may be pegged depends on what is buried under it, and that answer often arrives too late to redesign around. That is why we ask for the access route, the fixing rules, the power allocation and the build-up window in writing before anything is cut, rather than treating any of them as a site problem.
More in Delhi
Exhibiting soon? Let's build your stall.